Craftsman 315.21829 manual To Replace the Blade, See Figures57, Throm Plate Blade

Page 40

AWARNING." Before performing any adjustment,

make sure the tool is unplugged from the power suppty. Failureto heed this waTn'lngcoutdresu)tin serious persona_injury.

AWARNING: Blades coast after turn off. Possib}e

serious injury can occur if hands come in contact with blade.

The table sew has been adjusted at the factory for mak- ingvery accurate cuts. However, some of the components might have been jarred out of alignmentduringshipping. ALso,over a period of t'rne,rsediustmentwill probably

become necessary due to wear.

3"0avoid unnecessary setups and adjustmen*.s,a good practice is to check your setups carefullywith a fram- ing square and make practice cuts in scrap wood before making finish cuts in good workpiaces. Do not start any adjustments until you have checked with a square and made test cuts to be sure adjustments are needed.

TO REPLACE THE BLADE

See Figures57 - 59.

•Unplug the saw.

•Lowerthe saw blade, raise the blade guard, and remove the throet plate.

•Make sure the bevel lockinglever is securelypushed to the felt. Raise the sew bladeto its full height by turning

the haight/beve_ adjusting handwheelclockwise.

•Using the smallblade wrench, insertthe flat open and into the fiats on the arbor shaft.

•Insertthe closed and of the largeblade wrench over the

hax nut. Holding bo_.hwrenches li_nly, pull_.h_larger wrench forward to the f1"ontof the machine. Make sure

the blade nut is securelytightened. De not overtighten. NOTE: Arbor shaft hasleft hand threads.

Check allcrearancesfor free blade rotation. See To Set

the Scale to the Blade in this section. In cutting opera- tions, the scarewilt be set to the side of the blade where the cut will be measured and made.

THROM

PLATE

BLADE

NUT

Fig. 58

To replace the blade with an accessory blade, follow the instructionsprov'_edwith the accessory.

To Inatall e standard blade:

•Place thenew blade on the arbor shaft (the teeth must point down toward the fi'ontof the saw to work properly),

•Place the blade washer and the blade nut over the blade arbor.Be sure the dome side of the blade

washer f_cas ou_from. _a blade and that all items ere snugagainst the arbor housing,13ghtensecurely.

•Rotate the blade by hand to make sure it turnsfreely.

•Reinstallthe throat plate.

NOTE: Seaurelytighten throat plate screws. Do not al- low the throat plate to bow up above the table surface.

BLADETHROATPLATE

RMNG

KNIFE

 

 

©

 

 

BLAI)E

LARGE

SMALL

 

BLADE

BLADE

 

WRENCH

WRENCH

Fig. 59

 

 

Fig. 57

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents 10 in. Table SAW Customer Help Line 983000-693 15-05ONE Year Full Warranty on Craftsman Tool Always Keep the Blade Guard and Riving Keep Blades CLEAN, SHARP, AndwithKNIFE/SPREADER/SPLITTER in Place and in working order Blade Coasts After Being Turned OFF Before Making a CUT, be Sure ALL Adjust Ments are SecureAlways USE a Push Stick for Ripping NAR Avoid Awkward Operations and Hand Save These INSTRUCTIONS. Refer to themMinutes Time Symbol Name Desig NATION/EXPLANATIO NJmin Symbol Signal Awarning Caiion Meaning Your nearest Authorized Service Center for repairWhen servicing, use onyidenticalreplacement parts Servicingrequires extreme care and knowledgeSAW Receptacle Motor Power Electrical Connection Speed and WiringExtension Cords Grounding InstructionsCutter Head planers and Jointera Number ofturnscompletedby a spinningobjectin one minute120 V, 60 Hz AC only Product SpecficationsAmperes Know Your Table SAW See FigureOperatingcomponents Blades Combinationflatblade SquarescrewdriverThefollowing items are included with your table saw Small BadeWrench@ D Thefolidwing items are includedwith your table sawUnpacking To Open the LEG StandSee Figures 7 BaseTOSECURE/LEVELTHESAW See F-igum9See Figures 10 Sliding miter tableSee F-tre Bevel HandleSee Figures 13 TOUNLOCK/MOVETHERAILS ReleaseTochecksawbladeinstallation To Install the Sliding Miter Table and Miter FenceSee Figures fg Lockingclamps Throat Plate Small Wrench Large BladeoSee Flours21 SeeRIW ANTI-KICKBACKSHIMS HNS Applications Not recommended can resultin serious personal injuryBasic Operation of the Table SAW Causes of Kickback Avoiding KickbackUse the right type of blade for the cut being made Cutting AidsCutting Tips Types of CutsRIP CUT Mitercut Compoundbevelmitercut HOW to Make a Featherboard Diameter HOW to Mount a FeatherboardFeatherboard See F/gumChecking Sliding Miter Table and Making Adjustments TochangethebladedepthSee Rgure Not Front of miter base is on infead se of sawTo Adjust The Miter Base sectionthat follows Check Miter Fence AlignmentTo Adjust the Miter Base Mitertable Slides To Adjust the Miter FenceTo Adjust Quick Stop StopSee F=Jgure39 Makingcuts Test cut on scrap wood firstMaking a Cross CUT See Figures40.saw for the cut work Fence Making a Miter CUTSee F-agure43 See Ffeures44Fiouspersonalinjury BEVELRiP. CUT 8LADE Angled Scale Making a Compound Bevel Miter CUTMaking a Large Panel CUT See gMaking a Dado CUT NON-THROUGHCUT Guard Blade Removed Push StickAccessory Table Usage Knobbolt Nutbetween Adjustment ScrewsRear Table Clampng BracketToinstallguidefencebrackets NUTTo Install BIT and Throat Plate ToinstallrouterSee Ftgure55 To Replace the Blade See Figures57Throm Plate Blade Bladethroatplate Rmng Knife Blaie Large Small WrenchSee Figures 60 Framing Square Rivingblade KnifeTo Adjust the Miter Gauge To Adjust the Bevel Locking Lever HEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew SetscrewBlade Screws HANDLEFigToaugnthemiterlockingclamps ScrewLocker Bracket Assembly GeneralLubrication ElevatingshaftSolution CauseProblem Cause Check and adjustthe rip fence Reeharpenor set bladeLockinglever is not at full left position BJadenot proper for rip cutFORlEG Standassembly Craftsman 10 in. Table SAW Model noParts List Figure a Craftsman 10 in. Table SAW Model NO, 3t5.2t8290Parts List QtyCraftsman 10 in. Table SAW- Model no Key PartNumber Deecdptlon Description QtyScrew Craftsman t0 in. Table SAW Model no t5.218290 Figure F Miter Gauge Assembly Craftsman 10 in. Table SAW Mooel noA181014601 Craftsman t0 in. Table SAW Model no FiguregKey Part Number DescdpUon Qty Description Parts List for Figure G411061704 Call anytime, day or night U.S.A. and Canada Call anytime, day or night U.S.A. only

315.21829 specifications

The Craftsman 315.21829 is a versatile and robust power tool designed for a variety of home improvement and woodworking tasks. Known for its reliability, this model is part of the Craftsman family, a brand that has built a reputation for offering user-friendly tools that provide high performance without compromising on safety and comfort.

One of the standout features of the Craftsman 315.21829 is its powerful motor, delivering ample horsepower to tackle demanding jobs. Whether you are cutting, sanding, or drilling, this tool ensures efficient operation and quick results. The design reflects an emphasis on power and precision, enabling users to achieve professional-quality finishes.

The ergonomic design of the Craftsman 315.21829 includes a comfortable grip, which reduces fatigue during extended use. This aspect is particularly important for both DIY enthusiasts and professionals who often spend long hours working on projects. The lightweight nature of the tool also contributes to its ease of use, making it suitable for a wide range of applications around the home and workshop.

A key technological feature of the Craftsman 315.21829 is its variable speed control, allowing users to adjust the tool's speed according to the specific requirements of the task at hand. This flexibility enhances control and precision, especially when working with delicate materials or intricate designs. The built-in safety features provide added peace of mind, ensuring that the tool operates under safe conditions at all times.

Another highlight is the compatibility with a wide range of accessories, which enhances the versatility of the Craftsman 315.21829. Users can easily switch between tasks, whether they are drilling holes, driving screws, or finishing surfaces. This adaptability makes it a valuable addition to any toolkit.

Overall, the Craftsman 315.21829 stands out for its combination of power, versatility, and user-friendly design. It caters to both seasoned professionals and DIY novices, enabling a wide array of projects to be completed with ease and precision. With its robust features and reliable performance, this tool continues to be a favorite in the realm of home improvement and woodworking.
Top Page Image Contents