Craftsman 315.21829 manual Toaugnthemiterlockingclamps, Screw

Page 44

TOAUGNTHEMITERLOCKINGCLAMPS

See Figure 66.

The miter locking clamps are preset at the factory but may requireadjustingafter extended use or if damage occursin shipping.

•Unplug the saw.

•Loosen the set screw behind each lockingclamp.

•Loosen the screw on top of each Iockingclamp.

•Uft the locldng clamp to the up position,

•Push the clamp forward tight against the front railto bringthe c_p into aiigr_'_ent.

•When the clamps are correctlypositioned, retightenthe scows and the set screws.

•Push both front and rear miter lockingclamps down to secure the sidingmiter table.

SCREW

Fig. 66

TO ADJUST THE FRONT AND REAR RAIL

CLAMPS

See Rgure 67.

The rail cramps ate located below the raUsand ensure tight attachment of the rail. Followrngextended use, the rail holder nut inside the rails may need adjusting.

•Unplug the saw.

•Remove the miter table and accessory tabla.

•Remove the _ont emdrear rails by looseningthe rail crampsand dlding the rai_soff.

•Rotate each rail clamp to the {sft unti{it hits or comes in correct with the bo'_omot the saw table.

•Tighten rait holder nut until it is snug.

•Loosen rail holder nut one-fourth (1/4) turn.

•Replace the rails and check the rail clamps.

RAILHOLOER

NUT

RAIL

CLAMP

WASHER

HE)(MOUNTING

BOLT

Fig. 67

TO ADJUST THE ACCESSORY TABLE

See Rgure 68.

After extended use, the acce..-_,tab/e may work loose caus(_ th_ accessory table to be {oos_ o_ the ra'_s.

Foi(ow the steps below, when adjustmentsare required:

•Unplug the saw.

•Remove the hex nut on the lever using s 3/8 in. nut driver.

•Remove t_e backup p{ateand spring plate. Rotate the springplate 180° and reinstallon the handle shaft.

•Reassemble all parts end tighten hex nut securely.

NOTE; The spring plate offers two ends for use before re_[uiringreplacement.

ACCESSORYTABLE

LEVER

HAl

RING

_"IAFT

SPRINGPLATE

 

BACKUP

HEXNUT

PLATE

 

F_.68

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents 10 in. Table SAW Customer Help Line 983000-693 15-05ONE Year Full Warranty on Craftsman Tool KNIFE/SPREADER/SPLITTER in Place and in working order Keep Blades CLEAN, SHARP, AndwithAlways Keep the Blade Guard and Riving Always USE a Push Stick for Ripping NAR Before Making a CUT, be Sure ALL Adjust Ments are SecureBlade Coasts After Being Turned OFF Avoid Awkward Operations and Hand Save These INSTRUCTIONS. Refer to themJmin Symbol Name Desig NATION/EXPLANATIO NMinutes Time Symbol Signal Awarning Caiion Meaning Your nearest Authorized Service Center for repairWhen servicing, use onyidenticalreplacement parts Servicingrequires extreme care and knowledgeSAW Receptacle Motor Power Electrical Connection Speed and WiringExtension Cords Grounding InstructionsCutter Head planers and Jointera Number ofturnscompletedby a spinningobjectin one minuteAmperes Product Specfications120 V, 60 Hz AC only Know Your Table SAW See FigureOperatingcomponents Blades Combinationflatblade SquarescrewdriverThefollowing items are included with your table saw Small BadeWrench@ D Thefolidwing items are includedwith your table sawUnpacking To Open the LEG StandSee Figures 7 BaseTOSECURE/LEVELTHESAW See F-igum9See Figures 10 Sliding miter tableSee Figures 13 Bevel HandleSee F-tre TOUNLOCK/MOVETHERAILS ReleaseTochecksawbladeinstallation To Install the Sliding Miter Table and Miter FenceSee Figures fg Lockingclamps Throat Plate Small Wrench Large BladeoSee Flours21 SeeBasic Operation of the Table SAW Not recommended can resultin serious personal injuryRIW ANTI-KICKBACKSHIMS HNS Applications Causes of Kickback Avoiding KickbackUse the right type of blade for the cut being made Cutting AidsRIP CUT Mitercut Compoundbevelmitercut Types of CutsCutting Tips HOW to Make a Featherboard Diameter HOW to Mount a FeatherboardFeatherboard See F/gumChecking Sliding Miter Table and Making Adjustments TochangethebladedepthSee Rgure Not Front of miter base is on infead se of sawTo Adjust The Miter Base sectionthat follows Check Miter Fence AlignmentTo Adjust the Miter Base Mitertable Slides To Adjust the Miter FenceTo Adjust Quick Stop StopSee F=Jgure39 Makingcuts Test cut on scrap wood firstMaking a Cross CUT See Figures40.saw for the cut work Fence Making a Miter CUTSee F-agure43 See Ffeures44Fiouspersonalinjury BEVELRiP. CUT 8LADE Angled Scale Making a Compound Bevel Miter CUTMaking a Large Panel CUT See gMaking a Dado CUT NON-THROUGHCUT Guard Blade Removed Push StickAccessory Table Usage Knobbolt Nutbetween Adjustment ScrewsRear Table Clampng BracketToinstallguidefencebrackets NUTSee Ftgure55 ToinstallrouterTo Install BIT and Throat Plate To Replace the Blade See Figures57Throm Plate Blade Bladethroatplate Rmng Knife Blaie Large Small WrenchSee Figures 60 Framing Square Rivingblade KnifeTo Adjust the Miter Gauge To Adjust the Bevel Locking Lever HEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew SetscrewBlade Screws HANDLEFigToaugnthemiterlockingclamps ScrewLocker Bracket Assembly GeneralLubrication ElevatingshaftSolution CauseProblem Cause Check and adjustthe rip fence Reeharpenor set bladeLockinglever is not at full left position BJadenot proper for rip cutFORlEG Standassembly Craftsman 10 in. Table SAW Model noParts List Figure a Craftsman 10 in. Table SAW Model NO, 3t5.2t8290Parts List QtyCraftsman 10 in. Table SAW- Model no Key PartNumber Deecdptlon Description QtyScrew Craftsman t0 in. Table SAW Model no t5.218290 Figure F Miter Gauge Assembly Craftsman 10 in. Table SAW Mooel noA181014601 Craftsman t0 in. Table SAW Model no Figureg411061704 Parts List for Figure GKey Part Number DescdpUon Qty Description Call anytime, day or night U.S.A. and Canada Call anytime, day or night U.S.A. only

315.21829 specifications

The Craftsman 315.21829 is a versatile and robust power tool designed for a variety of home improvement and woodworking tasks. Known for its reliability, this model is part of the Craftsman family, a brand that has built a reputation for offering user-friendly tools that provide high performance without compromising on safety and comfort.

One of the standout features of the Craftsman 315.21829 is its powerful motor, delivering ample horsepower to tackle demanding jobs. Whether you are cutting, sanding, or drilling, this tool ensures efficient operation and quick results. The design reflects an emphasis on power and precision, enabling users to achieve professional-quality finishes.

The ergonomic design of the Craftsman 315.21829 includes a comfortable grip, which reduces fatigue during extended use. This aspect is particularly important for both DIY enthusiasts and professionals who often spend long hours working on projects. The lightweight nature of the tool also contributes to its ease of use, making it suitable for a wide range of applications around the home and workshop.

A key technological feature of the Craftsman 315.21829 is its variable speed control, allowing users to adjust the tool's speed according to the specific requirements of the task at hand. This flexibility enhances control and precision, especially when working with delicate materials or intricate designs. The built-in safety features provide added peace of mind, ensuring that the tool operates under safe conditions at all times.

Another highlight is the compatibility with a wide range of accessories, which enhances the versatility of the Craftsman 315.21829. Users can easily switch between tasks, whether they are drilling holes, driving screws, or finishing surfaces. This adaptability makes it a valuable addition to any toolkit.

Overall, the Craftsman 315.21829 stands out for its combination of power, versatility, and user-friendly design. It caters to both seasoned professionals and DIY novices, enabling a wide array of projects to be completed with ease and precision. With its robust features and reliable performance, this tool continues to be a favorite in the realm of home improvement and woodworking.
Top Page Image Contents