Craftsman 315.21829 manual BEVELRiP. CUT, 8LADE Angled Scale Making a Compound Bevel Miter CUT

Page 34

= When the out la made, turn the saw off. Wait for the blade to come to a complete stop before removingthe workplace.

•After the blade has stopped oomplateiy, remove the cutoff stock.

•Grasp the workplece from the lead end (the and fed into the b{ade first) and carefully remove it from the table.

BEVELRiP. CUT

8LADE

ANGLED

SCALE

\

Fig. 46

MAKING A COMPOUND (BEVEL) MITER CUT

See Figure 47.

It is recommended that you place the piece to be saved on the left side of the blade and that you make a test cut on scrap wood firsL

_1, WARNING: Make sure the blade guard ass_"nbly

is installedand working propedy to avoid sadoue posaiblainjury.

•Remove the rip fence by liftingthe lock down handle,

•Unlock:he bevel locking lever.

•Adjust the bevel angle to the desired setting.

•Lock the bevel locking lever.

•Set the saw blade to the correct depth.

•Loosen the lock knob on the miter gauge, set the miter gaugeto the desired angle and tighten lock knob.

•Turnthe power switch to the ON position.

•Positionthe workpiece fiat on the table with the edge flushagainst the miter gauge. Let the blade build up to full speed before feeding the workplace Into the blade.

•Advance the workplace and the miter gauge toward

the blade. Keep the workpiece flushagainst the miter gauge. Push the miter gauge and workplace toward the blade. Stand slightlyto the side of the wood as

it contacts the blade to reduos the chance of injury should kickback occur.

IIWhen the out Is made, turn the saw off. Wait for the blade to come to a complete stop beforeremovingthe workplace.

•After the blade has stopped completely,remove the cutoff stock.

COMPOUND(BEVEL)MITERCUT

PL_ RIGHTHAND

ONWORKPIECEAND

MR'ERGAUGEHERE

34

Image 34

Contents 10 in. Table SAW Customer Help Line 983000-693 15-05ONE Year Full Warranty on Craftsman Tool Always Keep the Blade Guard and Riving Keep Blades CLEAN, SHARP, AndwithKNIFE/SPREADER/SPLITTER in Place and in working order Blade Coasts After Being Turned OFF Before Making a CUT, be Sure ALL Adjust Ments are SecureAlways USE a Push Stick for Ripping NAR Avoid Awkward Operations and Hand Save These INSTRUCTIONS. Refer to themMinutes Time Symbol Name Desig NATION/EXPLANATIO NJmin When servicing, use onyidenticalreplacement parts Symbol Signal Awarning Caiion MeaningYour nearest Authorized Service Center for repair Servicingrequires extreme care and knowledgeExtension Cords SAW Receptacle Motor Power Electrical ConnectionSpeed and Wiring Grounding InstructionsCutter Head planers and Jointera Number ofturnscompletedby a spinningobjectin one minute120 V, 60 Hz AC only Product SpecficationsAmperes Know Your Table SAW See FigureOperatingcomponents Blades Combinationflatblade SquarescrewdriverThefollowing items are included with your table saw Small BadeWrench@ D Thefolidwing items are includedwith your table sawSee Figures 7 UnpackingTo Open the LEG Stand BaseSee Figures 10 TOSECURE/LEVELTHESAWSee F-igum9 Sliding miter tableSee F-tre Bevel HandleSee Figures 13 TOUNLOCK/MOVETHERAILS ReleaseSee Figures fg TochecksawbladeinstallationTo Install the Sliding Miter Table and Miter Fence Lockingclamps Throat Plate Small Wrench Large BladeoSee Flours21 SeeRIW ANTI-KICKBACKSHIMS HNS Applications Not recommended can resultin serious personal injuryBasic Operation of the Table SAW Use the right type of blade for the cut being made Causes of KickbackAvoiding Kickback Cutting AidsCutting Tips Types of CutsRIP CUT Mitercut Compoundbevelmitercut Featherboard HOW to Make a FeatherboardDiameter HOW to Mount a Featherboard See F/gumSee Rgure Checking Sliding Miter Table and Making AdjustmentsTochangethebladedepth Not Front of miter base is on infead se of sawTo Adjust The Miter Base sectionthat follows Check Miter Fence AlignmentTo Adjust the Miter Base Mitertable Slides To Adjust the Miter FenceTo Adjust Quick Stop StopSee F=Jgure39 Making a Cross CUT Makingcuts Test cut on scrap wood first See Figures40See F-agure43 .saw for the cut workFence Making a Miter CUT See Ffeures44Fiouspersonalinjury BEVELRiP. CUT 8LADE Angled Scale Making a Compound Bevel Miter CUTMaking a Large Panel CUT See gMaking a Dado CUT NON-THROUGHCUT Guard Blade Removed Push StickRear Accessory Table UsageKnobbolt Nutbetween Adjustment Screws Table Clampng BracketToinstallguidefencebrackets NUTTo Install BIT and Throat Plate ToinstallrouterSee Ftgure55 Throm Plate Blade To Replace the BladeSee Figures57 Bladethroatplate Rmng Knife Blaie Large Small WrenchSee Figures 60 Framing Square Rivingblade KnifeTo Adjust the Miter Gauge Blade Screws To Adjust the Bevel Locking LeverHEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew Setscrew HANDLEFigToaugnthemiterlockingclamps ScrewLubrication Locker Bracket AssemblyGeneral ElevatingshaftSolution CauseLockinglever is not at full left position Problem CauseCheck and adjustthe rip fence Reeharpenor set blade BJadenot proper for rip cutFORlEG Standassembly Craftsman 10 in. Table SAW Model noParts List Figure a Craftsman 10 in. Table SAW Model NO, 3t5.2t8290Parts List QtyNumber Deecdptlon Craftsman 10 in. Table SAW- Model noKey Part Description QtyScrew Craftsman t0 in. Table SAW Model no t5.218290 Figure F Miter Gauge Assembly Craftsman 10 in. Table SAW Mooel noA181014601 Craftsman t0 in. Table SAW Model no FiguregKey Part Number DescdpUon Qty Description Parts List for Figure G411061704 Call anytime, day or night U.S.A. and Canada Call anytime, day or night U.S.A. only