Craftsman 315.21829 manual Tochecksawbladeinstallation, See Figures fg, Rear Rail

Page 20

TOCHECKSAWBLADEINSTALLATION

See Figure 18.

CAUTION: To work: properly,the saw blade teeth must point down toward the front of t'nesaw. Failure to do so could cause damage to the saw blade, the saw, or the workpisce.

•Lowerthe saw blade and remove the throat p_te.

•Make sure the bevel Locking lever is securely pushed to

the left. Raise the saw blade to its fu[I height by turning the height/bevel adjusting hsndwheel clockwise.

To Loosen the blade.

•Using ';hesmall blade wrench, place the flat open and on the fiats on the arbor shat'_.

•Insert the closed end of the large blade wrench over the hex nut Holding both wrenches firmly, pull the larger wrench forward to the front of the machine.

To *dghtenthe blade:

•Using the srnaflbradswrench, place the flat open end (rite the _(atson the arbor shaft.

•Insert the closed end of the large blade wrench over the hex nut. Holding both wrenches firmly,push the {argerwrench to the back of the machine. Make sure the blade nut is securelytightened. Do not ovsrtighten.

NOTE: Arbor shaft has left hand threads.

Check all clearancesfor free blade rotation. See To Set the Scale to the Blade in the AdjustmentSection. In

cutting operations,the scale wil} be set to the side of the blade where the cut will be measured and made.

TO INSTALL THE SLIDING MITER TABLE AND MITER FENCE

See Figures fg - 20,

•Remove the slidingrofter table from the storage area by pullingthe miter lockingclamps away from the saw ¢ablnst

•Install the sliding miter table assembly over the front and rear rails. Check that it slides easily on the rsi[s. Push both front miter looking clamps down evenlyon each side to secure, Repeat for both rear miter locking _arnps.

NOTE: Do not force miter look}rig clamps down. Tighten only to f_t "seated" position.

•Remove the miter fence from the miter fence storage on the side of the saw cabinet.

•To install the miter fence to the slidingmiter table, Ices-

en the adjusting clamp knobso the bolt hasenough olsaranoa to slide _nthe table slot,

LOCKINGCLAMPS

THROAT

PLATE

SMALL

WRENCH

LARGE

BLADEO

WRENCH

Fig. 18

SUDII_

MITER

TABt.EBASE

REAR

RAIL

Fig. 19

Mount the miter fence to the miter table by installing

the locater pin (below the miter fence) into holes =A", "B", =C", or "D". (Holes "A" and =D" are closest 1othe

b}ade).At the same time, place the attachment bolt in the s_ot.

NOTE: Holes =A" and "D" should be used for short pieces of wood and holes"B" and "C" should be used for long pieces of wood.

•Property a_}ust the miter indicatorto the scale on the end of the fence oppositethe locater pin.

•Retightan the adiusting ctarnp knob.

2O

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 10 in. Table SAW Customer Help Line 983000-693 15-05ONE Year Full Warranty on Craftsman Tool KNIFE/SPREADER/SPLITTER in Place and in working order Keep Blades CLEAN, SHARP, AndwithAlways Keep the Blade Guard and Riving Always USE a Push Stick for Ripping NAR Before Making a CUT, be Sure ALL Adjust Ments are SecureBlade Coasts After Being Turned OFF Avoid Awkward Operations and Hand Save These INSTRUCTIONS. Refer to themJmin Symbol Name Desig NATION/EXPLANATIO NMinutes Time Symbol Signal Awarning Caiion Meaning Your nearest Authorized Service Center for repairWhen servicing, use onyidenticalreplacement parts Servicingrequires extreme care and knowledgeSAW Receptacle Motor Power Electrical Connection Speed and WiringExtension Cords Grounding InstructionsCutter Head planers and Jointera Number ofturnscompletedby a spinningobjectin one minuteAmperes Product Specfications120 V, 60 Hz AC only Know Your Table SAW See FigureOperatingcomponents Blades Combinationflatblade SquarescrewdriverThefollowing items are included with your table saw Small BadeWrench@ D Thefolidwing items are includedwith your table sawUnpacking To Open the LEG StandSee Figures 7 BaseTOSECURE/LEVELTHESAW See F-igum9See Figures 10 Sliding miter tableSee Figures 13 Bevel HandleSee F-tre TOUNLOCK/MOVETHERAILS ReleaseTochecksawbladeinstallation To Install the Sliding Miter Table and Miter FenceSee Figures fg Lockingclamps Throat Plate Small Wrench Large BladeoSee Flours21 SeeBasic Operation of the Table SAW Not recommended can resultin serious personal injuryRIW ANTI-KICKBACKSHIMS HNS Applications Causes of Kickback Avoiding KickbackUse the right type of blade for the cut being made Cutting AidsRIP CUT Mitercut Compoundbevelmitercut Types of CutsCutting Tips HOW to Make a Featherboard Diameter HOW to Mount a FeatherboardFeatherboard See F/gumChecking Sliding Miter Table and Making Adjustments TochangethebladedepthSee Rgure Not Front of miter base is on infead se of sawTo Adjust The Miter Base sectionthat follows Check Miter Fence AlignmentTo Adjust the Miter Base Mitertable Slides To Adjust the Miter FenceTo Adjust Quick Stop StopSee F=Jgure39 Makingcuts Test cut on scrap wood firstMaking a Cross CUT See Figures40.saw for the cut work Fence Making a Miter CUTSee F-agure43 See Ffeures44Fiouspersonalinjury BEVELRiP. CUT 8LADE Angled Scale Making a Compound Bevel Miter CUTMaking a Large Panel CUT See gMaking a Dado CUT NON-THROUGHCUT Guard Blade Removed Push StickAccessory Table Usage Knobbolt Nutbetween Adjustment ScrewsRear Table Clampng BracketToinstallguidefencebrackets NUTSee Ftgure55 ToinstallrouterTo Install BIT and Throat Plate To Replace the Blade See Figures57Throm Plate Blade Bladethroatplate Rmng Knife Blaie Large Small WrenchSee Figures 60 Framing Square Rivingblade KnifeTo Adjust the Miter Gauge To Adjust the Bevel Locking Lever HEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew SetscrewBlade Screws HANDLEFigToaugnthemiterlockingclamps ScrewLocker Bracket Assembly GeneralLubrication ElevatingshaftSolution CauseProblem Cause Check and adjustthe rip fence Reeharpenor set bladeLockinglever is not at full left position BJadenot proper for rip cutFORlEG Standassembly Craftsman 10 in. Table SAW Model noParts List Figure a Craftsman 10 in. Table SAW Model NO, 3t5.2t8290Parts List QtyCraftsman 10 in. Table SAW- Model no Key PartNumber Deecdptlon Description QtyScrew Craftsman t0 in. Table SAW Model no t5.218290 Figure F Miter Gauge Assembly Craftsman 10 in. Table SAW Mooel noA181014601 Craftsman t0 in. Table SAW Model no Figureg411061704 Parts List for Figure GKey Part Number DescdpUon Qty Description Call anytime, day or night U.S.A. and Canada Call anytime, day or night U.S.A. only

315.21829 specifications

The Craftsman 315.21829 is a versatile and robust power tool designed for a variety of home improvement and woodworking tasks. Known for its reliability, this model is part of the Craftsman family, a brand that has built a reputation for offering user-friendly tools that provide high performance without compromising on safety and comfort.

One of the standout features of the Craftsman 315.21829 is its powerful motor, delivering ample horsepower to tackle demanding jobs. Whether you are cutting, sanding, or drilling, this tool ensures efficient operation and quick results. The design reflects an emphasis on power and precision, enabling users to achieve professional-quality finishes.

The ergonomic design of the Craftsman 315.21829 includes a comfortable grip, which reduces fatigue during extended use. This aspect is particularly important for both DIY enthusiasts and professionals who often spend long hours working on projects. The lightweight nature of the tool also contributes to its ease of use, making it suitable for a wide range of applications around the home and workshop.

A key technological feature of the Craftsman 315.21829 is its variable speed control, allowing users to adjust the tool's speed according to the specific requirements of the task at hand. This flexibility enhances control and precision, especially when working with delicate materials or intricate designs. The built-in safety features provide added peace of mind, ensuring that the tool operates under safe conditions at all times.

Another highlight is the compatibility with a wide range of accessories, which enhances the versatility of the Craftsman 315.21829. Users can easily switch between tasks, whether they are drilling holes, driving screws, or finishing surfaces. This adaptability makes it a valuable addition to any toolkit.

Overall, the Craftsman 315.21829 stands out for its combination of power, versatility, and user-friendly design. It caters to both seasoned professionals and DIY novices, enabling a wide array of projects to be completed with ease and precision. With its robust features and reliable performance, this tool continues to be a favorite in the realm of home improvement and woodworking.
Top Page Image Contents