Craftsman 315.21829 manual Cause, Solution

Page 46

Lookfortheseaccessories at Sears rata'd:

Item No. 9-22212	Zero Clearance Throat Plate
4070331	Dado Throat Plate
Item No. 9-22214	Micro-Position Rip-Fence Accessory
Item No. 9-22215Quick Fold Table
Item No. 9-22217	Long Miter/Rip Fence
Item No. 9-22220	Miter Clamp Kit

A

41& WARNING; To avoid risk of injury,use recommended dado and zero clearance throat plata when amp}eying a dado accessory.

IONLY USE 6 IN. STACK DADOES.

',=NEVER BEVEL DAJDO.

•NEVER USE ADJUSTABLE DADOES ON THIS SAW,

PROBLEM

Excess vibration.

Rip fence does not move smoothly.

Rip fence does not lock at

rear.

Cutting binds or burns work,

CAUSE

Blade is out of balance,

Blade is damaged.

Saw is not mounted securely.

Work surface is uneven.

Bladeis warped.

Rip fence not mounted c,on'e_tLy.

Rails are dirtyor sticky.

Clamp screw isout of adjustment.

Clamp screw isout of adjustment.

Blade is dull.

Blade is heeling.

Work is fed too fast

Rip fence ismisaUgned.

Riving knife is misaligced.

Wood iswarped.

SOLUTION]

Replace blade.

Replace blade.

Tightenall hardware.

Repositionon flat surface.

Adjust legs of op_onsl stand.

Check Saw Blade Inst_la_on. Replace blade if necessary

Remount therip fence.

Clean and wax mils.

Adjustclamp screw counterclockwise,

Adiustclamps_ew clockwise.

Replace or sharpen blade,

Align miterbase.

Slow the feed rats.

Align the _lpfence.

Adiust the dvlng knife with shims provided.

Replacethe wood. Always cut with convex side to table surface.

46

Image 46

Contents 10 in. Table SAW Customer Help Line 983000-693 15-05ONE Year Full Warranty on Craftsman Tool Always Keep the Blade Guard and Riving Keep Blades CLEAN, SHARP, AndwithKNIFE/SPREADER/SPLITTER in Place and in working order Blade Coasts After Being Turned OFF Before Making a CUT, be Sure ALL Adjust Ments are SecureAlways USE a Push Stick for Ripping NAR Avoid Awkward Operations and Hand Save These INSTRUCTIONS. Refer to themMinutes Time Symbol Name Desig NATION/EXPLANATIO NJmin When servicing, use onyidenticalreplacement parts Symbol Signal Awarning Caiion MeaningYour nearest Authorized Service Center for repair Servicingrequires extreme care and knowledgeExtension Cords SAW Receptacle Motor Power Electrical ConnectionSpeed and Wiring Grounding InstructionsCutter Head planers and Jointera Number ofturnscompletedby a spinningobjectin one minute120 V, 60 Hz AC only Product SpecficationsAmperes Know Your Table SAW See FigureOperatingcomponents Blades Combinationflatblade SquarescrewdriverThefollowing items are included with your table saw Small BadeWrench@ D Thefolidwing items are includedwith your table sawSee Figures 7 UnpackingTo Open the LEG Stand BaseSee Figures 10 TOSECURE/LEVELTHESAWSee F-igum9 Sliding miter tableSee F-tre Bevel HandleSee Figures 13 TOUNLOCK/MOVETHERAILS ReleaseSee Figures fg TochecksawbladeinstallationTo Install the Sliding Miter Table and Miter Fence Lockingclamps Throat Plate Small Wrench Large BladeoSee Flours21 SeeRIW ANTI-KICKBACKSHIMS HNS Applications Not recommended can resultin serious personal injuryBasic Operation of the Table SAW Use the right type of blade for the cut being made Causes of KickbackAvoiding Kickback Cutting AidsCutting Tips Types of CutsRIP CUT Mitercut Compoundbevelmitercut Featherboard HOW to Make a FeatherboardDiameter HOW to Mount a Featherboard See F/gumSee Rgure Checking Sliding Miter Table and Making AdjustmentsTochangethebladedepth Not Front of miter base is on infead se of sawTo Adjust The Miter Base sectionthat follows Check Miter Fence AlignmentTo Adjust the Miter Base Mitertable Slides To Adjust the Miter FenceTo Adjust Quick Stop StopSee F=Jgure39 Making a Cross CUT MakingcutsTest cut on scrap wood first See Figures40See F-agure43 .saw for the cut workFence Making a Miter CUT See Ffeures44Fiouspersonalinjury BEVELRiP. CUT 8LADE Angled Scale Making a Compound Bevel Miter CUTMaking a Large Panel CUT See gMaking a Dado CUT NON-THROUGHCUT Guard Blade Removed Push StickRear Accessory Table UsageKnobbolt Nutbetween Adjustment Screws Table Clampng BracketToinstallguidefencebrackets NUTTo Install BIT and Throat Plate ToinstallrouterSee Ftgure55 Throm Plate Blade To Replace the BladeSee Figures57 Bladethroatplate Rmng Knife Blaie Large Small WrenchSee Figures 60 Framing Square Rivingblade KnifeTo Adjust the Miter Gauge Blade Screws To Adjust the Bevel Locking Lever HEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew Setscrew HANDLEFigToaugnthemiterlockingclamps ScrewLubrication Locker Bracket AssemblyGeneral ElevatingshaftSolution CauseLockinglever is not at full left position Problem CauseCheck and adjustthe rip fence Reeharpenor set blade BJadenot proper for rip cutFORlEG Standassembly Craftsman 10 in. Table SAW Model noParts List Figure a Craftsman 10 in. Table SAW Model NO, 3t5.2t8290Parts List QtyNumber Deecdptlon Craftsman 10 in. Table SAW- Model noKey Part Description QtyScrew Craftsman t0 in. Table SAW Model no t5.218290 Figure F Miter Gauge Assembly Craftsman 10 in. Table SAW Mooel noA181014601 Craftsman t0 in. Table SAW Model no FiguregKey Part Number DescdpUon Qty Description Parts List for Figure G411061704 Call anytime, day or night U.S.A. and Canada Call anytime, day or night U.S.A. only