Craftsman 315.21829 manual Making a Large Panel CUT, See g

Page 35

MAKING A LARGE PANEL CUT

See Figure48.

Make sure the sew is properly securedto e work surface to avoidtipping from the weight of a large panel

_, WARNING: Make sure the b_ade guard assembly is installedand working properly to avoidserious pessibteinjury.

•Place a supportthe same height as the top of the saw

table behind the saw for the cut work. Add supportsto the sides as needed.

•Depending on the shape of the pansl, use the rip fence or miteTgauge, ff the panel is too large to use s_'herthe rip {once or the miter gauge, it is too {argofor this saw.

_IL WARNING: Nsvsr make freehand cuts {cutswithout

the miter gauge or rip fence), which can resultin seriousinjury.

•Make sure thewood does not touch the blade before you turn on the saw, Let the blade bu_d up to full speed beforefoeding the wood _,ntothe blade.

•When the work is oemplstod, press the switch offand remove the key.

lARGEPN(EL CUT

RIP FENCE

HEIGHT

ADJUSTING

HANDWHEEL

Fig. _-8

MAKING A NON-THROUGH CUT

See Figure4g.

Non-through cuts can be made with the grain (ripping)or across the grain (crosscut}.The use of a nOn-throughcut is essentialto cuttinggrooves,rabbets, and d,ad.oes.

NOTE: TtT_sis the onlytype out that is made without

the blade guard instsIled.Make sure the blade guard assembly la reinstalledupon completion of this type of cut.

Read the appropriate sectionwhich describesthe type of cut inaddition to this section on non-throughor dado

cuts. For example, if yournon-throughcut is a straight cross cut, read and understandthe sectionon straight

cross cuts before procaed{ng.

•Unplug the saw.

•Lower the blade and removethe screw holdingthe throat plate in place. Remove the throat plate.

•RaLsethe saw blade.

•Put the sew in angle mode by pushingthe bevel locking lavar to the right. Turnthe height adjusting hsndwheel until the b(ade indicster showsa 30" ar_jis.

Push the bevel locking{eversecurelyto the [eft to lock the angle,

•Loosen the two hex nuts st the base of the riving knife.

Do not remove hex nuts. Removethe rivingknife/ blade guard assembly.Retightanthe two hex nuts on the base,

•Lower the blade and insert the throat plate, then securelytighten the throat plate screw.

•Bring the blade backto gO°.

•Raise the blade _othe correcthaigh'tby tuTningthe height ad{ustinghandwheelcounterclockwise. NOTE: Carefullycheckall setups and rctsta the blade one fur{revolutionto assure properclearance before connecting saw to power source.

•Feed the workpiscs into the blade.

•Always use push blocks, push sticks,and feather- boards when makingnon-throughcuts to avoid the risk of seriousinjury,

_1= WARNING: When making a non-throughcut, the cutter is covered by the warY,piece during most ot the cut. Be alert to the exposed cutter at the start and finishof everycut to avoid the risk of personal injury.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Customer Help Line 983000-693 15-05 10 in. Table SAWONE Year Full Warranty on Craftsman Tool KNIFE/SPREADER/SPLITTER in Place and in working order Keep Blades CLEAN, SHARP, AndwithAlways Keep the Blade Guard and Riving Always USE a Push Stick for Ripping NAR Before Making a CUT, be Sure ALL Adjust Ments are SecureBlade Coasts After Being Turned OFF Save These INSTRUCTIONS. Refer to them Avoid Awkward Operations and HandJmin Symbol Name Desig NATION/EXPLANATIO NMinutes Time Servicingrequires extreme care and knowledge Symbol Signal Awarning Caiion MeaningYour nearest Authorized Service Center for repair When servicing, use onyidenticalreplacement partsGrounding Instructions SAW Receptacle Motor Power Electrical ConnectionSpeed and Wiring Extension CordsNumber ofturnscompletedby a spinningobjectin one minute Cutter Head planers and JointeraAmperes Product Specfications120 V, 60 Hz AC only See Figure Know Your Table SAWOperatingcomponents Combinationflatblade Squarescrewdriver BladesSmall BadeWrench Thefollowing items are included with your table sawThefolidwing items are includedwith your table saw @ DBase UnpackingTo Open the LEG Stand See Figures 7Sliding miter table TOSECURE/LEVELTHESAWSee F-igum9 See Figures 10See Figures 13 Bevel HandleSee F-tre Release TOUNLOCK/MOVETHERAILSLockingclamps Throat Plate Small Wrench Large Bladeo TochecksawbladeinstallationTo Install the Sliding Miter Table and Miter Fence See Figures fgSee See Flours21Basic Operation of the Table SAW Not recommended can resultin serious personal injuryRIW ANTI-KICKBACKSHIMS HNS Applications Cutting Aids Causes of KickbackAvoiding Kickback Use the right type of blade for the cut being madeRIP CUT Mitercut Compoundbevelmitercut Types of CutsCutting Tips See F/gum HOW to Make a FeatherboardDiameter HOW to Mount a Featherboard FeatherboardNot Front of miter base is on infead se of saw Checking Sliding Miter Table and Making AdjustmentsTochangethebladedepth See RgureCheck Miter Fence Alignment To Adjust The Miter Base sectionthat followsMitertable Slides To Adjust the Miter Fence To Adjust the Miter BaseStop To Adjust Quick StopSee F=Jgure39 See Figures40 MakingcutsTest cut on scrap wood first Making a Cross CUTSee Ffeures44 .saw for the cut workFence Making a Miter CUT See F-agure43Fiouspersonalinjury 8LADE Angled Scale Making a Compound Bevel Miter CUT BEVELRiP. CUTSee g Making a Large Panel CUTNON-THROUGHCUT Guard Blade Removed Push Stick Making a Dado CUTTable Clampng Bracket Accessory Table UsageKnobbolt Nutbetween Adjustment Screws RearNUT ToinstallguidefencebracketsSee Ftgure55 ToinstallrouterTo Install BIT and Throat Plate Bladethroatplate Rmng Knife Blaie Large Small Wrench To Replace the BladeSee Figures57 Throm Plate BladeFraming Square Rivingblade Knife See Figures 60To Adjust the Miter Gauge HANDLEFig To Adjust the Bevel Locking LeverHEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew Setscrew Blade ScrewsScrew ToaugnthemiterlockingclampsElevatingshaft Locker Bracket AssemblyGeneral LubricationCause SolutionBJadenot proper for rip cut Problem CauseCheck and adjustthe rip fence Reeharpenor set blade Lockinglever is not at full left positionCraftsman 10 in. Table SAW Model no FORlEG StandassemblyCraftsman 10 in. Table SAW Model NO, 3t5.2t8290 Parts List Figure aQty Parts ListDescription Qty Craftsman 10 in. Table SAW- Model noKey Part Number DeecdptlonScrew Craftsman t0 in. Table SAW Model no t5.218290 Craftsman 10 in. Table SAW Mooel no Figure F Miter Gauge AssemblyA181014601 Figureg Craftsman t0 in. Table SAW Model no411061704 Parts List for Figure GKey Part Number DescdpUon Qty Description Call anytime, day or night U.S.A. only Call anytime, day or night U.S.A. and Canada

315.21829 specifications

The Craftsman 315.21829 is a versatile and robust power tool designed for a variety of home improvement and woodworking tasks. Known for its reliability, this model is part of the Craftsman family, a brand that has built a reputation for offering user-friendly tools that provide high performance without compromising on safety and comfort.

One of the standout features of the Craftsman 315.21829 is its powerful motor, delivering ample horsepower to tackle demanding jobs. Whether you are cutting, sanding, or drilling, this tool ensures efficient operation and quick results. The design reflects an emphasis on power and precision, enabling users to achieve professional-quality finishes.

The ergonomic design of the Craftsman 315.21829 includes a comfortable grip, which reduces fatigue during extended use. This aspect is particularly important for both DIY enthusiasts and professionals who often spend long hours working on projects. The lightweight nature of the tool also contributes to its ease of use, making it suitable for a wide range of applications around the home and workshop.

A key technological feature of the Craftsman 315.21829 is its variable speed control, allowing users to adjust the tool's speed according to the specific requirements of the task at hand. This flexibility enhances control and precision, especially when working with delicate materials or intricate designs. The built-in safety features provide added peace of mind, ensuring that the tool operates under safe conditions at all times.

Another highlight is the compatibility with a wide range of accessories, which enhances the versatility of the Craftsman 315.21829. Users can easily switch between tasks, whether they are drilling holes, driving screws, or finishing surfaces. This adaptability makes it a valuable addition to any toolkit.

Overall, the Craftsman 315.21829 stands out for its combination of power, versatility, and user-friendly design. It caters to both seasoned professionals and DIY novices, enabling a wide array of projects to be completed with ease and precision. With its robust features and reliable performance, this tool continues to be a favorite in the realm of home improvement and woodworking.
Top Page Image Contents