Craftsman 315.21829 manual Tosecure/Levelthesaw, See F-igum9, See Figures 10, Sliding miter table

Page 17

TOSECURE/LEVELTHESAW

See F-igum9.

With the leg stand open and the table saw resting on a fiat, level surface, the saw shou]d not move or rook fl'om side to side.

ff the sew rests on the wheels and roils, [oosaneach

wheel stop by turning counterclockwise.The leg stand should met on each stop only slightly.If the wheel stop is

turned too much, the stop will interferewith the opening and closing motion of the leg stand.

if the saw rocks from side to side, the levelingfeet need adiustlng until the leg stand is balanced.

•Loosen both the top and bottomwing nuts.

•Lift the saw slightlyso that you may turn the kiveiin9 foot untilthe leg stand no longerrocks.

•Turning ctookwise wilt lower thefoot

•Turning countarclockwisaw_llra'lsathe fog

WINGNUT

FOOT

Fig. g

TO S'fORE THE TABLE SAW ACCESSORIES

See Figures 10. - 11

The table saw has two convenientstorage areas specifi- cally designed for the saw'saccessories. These accesso-

ries must be sooure_ystored priorto closing the leg stand and moving the saw.

The rip fence, miter fence, and miter gauge shouldbe stored in the brackets located on the side of the saw

cabinet. Simply snap each accessoryin place to hold _t securely.

Storage hooks for the slidingmiter table are located on the back of the saw cabinet. This storagearea is to be used onlyfor moving the saw or when the saw is not being used.

NOTE: During operation of the saw, the slidingmiter table must be mounted on the mile. NEVER operate the sew with the sliding miter table in the storage position because it blocksthe dust exhaust port.

MZTER

RIPFENCE

Fig. 10

Stand facing the back of the table saw. The longest part of the miter table base must be stored to the left. To secure

the sliding miter table:

•Restthe slidingmiter table on the bottom right-hand storage hook and +,hemiter base on the lower miter bottom left-hand hook.

IAlignthe bottom miter lookingcfe_npwith the bottom left storage hock. Push the slidingm'rtertable back

toward the cabinet _zntilit is restingagainst all four hooks.

•Look the miter lookingclamps on the left by pushing clamps toward the side of the oabinst securingthe miter table in place.

MI'IER

STORAGE

HOOK

SLIDING

MITER

TABLE

STOP,ABEHDDK

F_g;11

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Customer Help Line 983000-693 15-05 10 in. Table SAWONE Year Full Warranty on Craftsman Tool KNIFE/SPREADER/SPLITTER in Place and in working order Keep Blades CLEAN, SHARP, AndwithAlways Keep the Blade Guard and Riving Always USE a Push Stick for Ripping NAR Before Making a CUT, be Sure ALL Adjust Ments are SecureBlade Coasts After Being Turned OFF Save These INSTRUCTIONS. Refer to them Avoid Awkward Operations and HandJmin Symbol Name Desig NATION/EXPLANATIO NMinutes Time Your nearest Authorized Service Center for repair Symbol Signal Awarning Caiion MeaningWhen servicing, use onyidenticalreplacement parts Servicingrequires extreme care and knowledgeSpeed and Wiring SAW Receptacle Motor Power Electrical ConnectionExtension Cords Grounding InstructionsNumber ofturnscompletedby a spinningobjectin one minute Cutter Head planers and JointeraAmperes Product Specfications120 V, 60 Hz AC only See Figure Know Your Table SAWOperatingcomponents Combinationflatblade Squarescrewdriver BladesSmall BadeWrench Thefollowing items are included with your table sawThefolidwing items are includedwith your table saw @ DTo Open the LEG Stand UnpackingSee Figures 7 BaseSee F-igum9 TOSECURE/LEVELTHESAWSee Figures 10 Sliding miter tableSee Figures 13 Bevel HandleSee F-tre Release TOUNLOCK/MOVETHERAILSTo Install the Sliding Miter Table and Miter Fence TochecksawbladeinstallationSee Figures fg Lockingclamps Throat Plate Small Wrench Large BladeoSee See Flours21Basic Operation of the Table SAW Not recommended can resultin serious personal injuryRIW ANTI-KICKBACKSHIMS HNS Applications Avoiding Kickback Causes of KickbackUse the right type of blade for the cut being made Cutting AidsRIP CUT Mitercut Compoundbevelmitercut Types of CutsCutting Tips Diameter HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard See F/gumTochangethebladedepth Checking Sliding Miter Table and Making AdjustmentsSee Rgure Not Front of miter base is on infead se of sawCheck Miter Fence Alignment To Adjust The Miter Base sectionthat followsMitertable Slides To Adjust the Miter Fence To Adjust the Miter BaseStop To Adjust Quick StopSee F=Jgure39 Test cut on scrap wood first MakingcutsMaking a Cross CUT See Figures40Fence Making a Miter CUT .saw for the cut workSee F-agure43 See Ffeures44Fiouspersonalinjury 8LADE Angled Scale Making a Compound Bevel Miter CUT BEVELRiP. CUTSee g Making a Large Panel CUTNON-THROUGHCUT Guard Blade Removed Push Stick Making a Dado CUTKnobbolt Nutbetween Adjustment Screws Accessory Table UsageRear Table Clampng BracketNUT ToinstallguidefencebracketsSee Ftgure55 ToinstallrouterTo Install BIT and Throat Plate See Figures57 To Replace the BladeThrom Plate Blade Bladethroatplate Rmng Knife Blaie Large Small WrenchFraming Square Rivingblade Knife See Figures 60To Adjust the Miter Gauge HEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew Setscrew To Adjust the Bevel Locking LeverBlade Screws HANDLEFigScrew ToaugnthemiterlockingclampsGeneral Locker Bracket AssemblyLubrication ElevatingshaftCause SolutionCheck and adjustthe rip fence Reeharpenor set blade Problem CauseLockinglever is not at full left position BJadenot proper for rip cutCraftsman 10 in. Table SAW Model no FORlEG StandassemblyCraftsman 10 in. Table SAW Model NO, 3t5.2t8290 Parts List Figure aQty Parts ListKey Part Craftsman 10 in. Table SAW- Model noNumber Deecdptlon Description QtyScrew Craftsman t0 in. Table SAW Model no t5.218290 Craftsman 10 in. Table SAW Mooel no Figure F Miter Gauge AssemblyA181014601 Figureg Craftsman t0 in. Table SAW Model no411061704 Parts List for Figure GKey Part Number DescdpUon Qty Description Call anytime, day or night U.S.A. only Call anytime, day or night U.S.A. and Canada

315.21829 specifications

The Craftsman 315.21829 is a versatile and robust power tool designed for a variety of home improvement and woodworking tasks. Known for its reliability, this model is part of the Craftsman family, a brand that has built a reputation for offering user-friendly tools that provide high performance without compromising on safety and comfort.

One of the standout features of the Craftsman 315.21829 is its powerful motor, delivering ample horsepower to tackle demanding jobs. Whether you are cutting, sanding, or drilling, this tool ensures efficient operation and quick results. The design reflects an emphasis on power and precision, enabling users to achieve professional-quality finishes.

The ergonomic design of the Craftsman 315.21829 includes a comfortable grip, which reduces fatigue during extended use. This aspect is particularly important for both DIY enthusiasts and professionals who often spend long hours working on projects. The lightweight nature of the tool also contributes to its ease of use, making it suitable for a wide range of applications around the home and workshop.

A key technological feature of the Craftsman 315.21829 is its variable speed control, allowing users to adjust the tool's speed according to the specific requirements of the task at hand. This flexibility enhances control and precision, especially when working with delicate materials or intricate designs. The built-in safety features provide added peace of mind, ensuring that the tool operates under safe conditions at all times.

Another highlight is the compatibility with a wide range of accessories, which enhances the versatility of the Craftsman 315.21829. Users can easily switch between tasks, whether they are drilling holes, driving screws, or finishing surfaces. This adaptability makes it a valuable addition to any toolkit.

Overall, the Craftsman 315.21829 stands out for its combination of power, versatility, and user-friendly design. It caters to both seasoned professionals and DIY novices, enabling a wide array of projects to be completed with ease and precision. With its robust features and reliable performance, this tool continues to be a favorite in the realm of home improvement and woodworking.
Top Page Image Contents