Craftsman 315.21829 Makingcuts, Test cut on scrap wood first, Making a Cross CUT, See Figures40

Page 31

MAKINGCUTS

Thebladeprovidedwiththe saw is a high-quality combi- nation blade sultabTefor ripping and crossout operations.

_1, WARNING: Do not use blades rated less than the speed of this tool. FaiKureto heed this warningcould resultin perscnal injury.

Use the miter gauge when making cross, miter,bevel, and compound miter cuts. To secure the angle, lock the miter gauge in place by twisting the lock knob clockwise. Always tighten the lock knobsecurely in pJaoebefore use.

NOTE=It is recommended that you place the piece to be saved on the left side of the blade and that you make a

test cut on scrap wood first.

MAKING A CROSS CUT

See Figures40 - 41.

WARNING: Using the rip fence as a cutoff gauge when crosscuttingwit1resultin kickback which can cause seriouspersonat injury.

WARNING=: Make sure the blade guard assembly is installed and working properly to avoid serious possible injury.

It is recommended you make test cuts on scrap wood.

•Remove the rip fence by liftingthe lockinghandle.

•Set the blade to the correct depth for the workpiece.

•Set the miter fence to 0 ° and tighten the lock knob.

CROSSCUT

PLACELEFTHANDON

WORKPIECEAND

MITERFENCEHERE

Fig. 40

SV//T_H

SWITCH°?

ON

\

SWITCHKEY

'8WITCHIN LOCI_DPOSITION

Rg. 41

•Place a support (the same height as saw table) behind the saw for the cut work.

•Make sure the wood is clear of the blade beforeturning on the saw.

•To turn the saw ON, lift the switch button.

•To turn saw OFF, press the switch button down.

NOTE: To prevent unauthorizeduse, remove the switch key as shown in figure 41.

•Let the blade build up to fullspeed before movingthe wot_piece _ntothe b_ade.

•Hold the workpieca firmlywith both hands on the miter gauge and feed the workpiece into the blade.

•When the cut_ made, turn the saw off. Wait for the

blade to come to a complete Hop betore removing the workpiese.

MAKING A RiP CUT

See Figure 42.

It is recommendedyou make a test cut on scrap wood.

,_ WARNING: Make sure the blade guard assembly is installedand working proper(y to avoid serious possibleinjLIry.

•Positionthe rip fence the desired distance from the blade for the out and sasurstylook the handle. Adjust the scale to zero at the cutting edge of the blade.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Customer Help Line 983000-693 15-05 10 in. Table SAWONE Year Full Warranty on Craftsman Tool Always Keep the Blade Guard and Riving Keep Blades CLEAN, SHARP, AndwithKNIFE/SPREADER/SPLITTER in Place and in working order Blade Coasts After Being Turned OFF Before Making a CUT, be Sure ALL Adjust Ments are SecureAlways USE a Push Stick for Ripping NAR Save These INSTRUCTIONS. Refer to them Avoid Awkward Operations and HandMinutes Time Symbol Name Desig NATION/EXPLANATIO NJmin Servicingrequires extreme care and knowledge Symbol Signal Awarning Caiion MeaningYour nearest Authorized Service Center for repair When servicing, use onyidenticalreplacement partsGrounding Instructions SAW Receptacle Motor Power Electrical ConnectionSpeed and Wiring Extension CordsNumber ofturnscompletedby a spinningobjectin one minute Cutter Head planers and Jointera120 V, 60 Hz AC only Product SpecficationsAmperes See Figure Know Your Table SAWOperatingcomponents Combinationflatblade Squarescrewdriver BladesSmall BadeWrench Thefollowing items are included with your table sawThefolidwing items are includedwith your table saw @ DBase UnpackingTo Open the LEG Stand See Figures 7Sliding miter table TOSECURE/LEVELTHESAWSee F-igum9 See Figures 10See F-tre Bevel HandleSee Figures 13 Release TOUNLOCK/MOVETHERAILSLockingclamps Throat Plate Small Wrench Large Bladeo TochecksawbladeinstallationTo Install the Sliding Miter Table and Miter Fence See Figures fgSee See Flours21RIW ANTI-KICKBACKSHIMS HNS Applications Not recommended can resultin serious personal injuryBasic Operation of the Table SAW Cutting Aids Causes of KickbackAvoiding Kickback Use the right type of blade for the cut being madeCutting Tips Types of CutsRIP CUT Mitercut Compoundbevelmitercut See F/gum HOW to Make a FeatherboardDiameter HOW to Mount a Featherboard FeatherboardNot Front of miter base is on infead se of saw Checking Sliding Miter Table and Making AdjustmentsTochangethebladedepth See RgureCheck Miter Fence Alignment To Adjust The Miter Base sectionthat followsMitertable Slides To Adjust the Miter Fence To Adjust the Miter BaseStop To Adjust Quick StopSee F=Jgure39 See Figures40 MakingcutsTest cut on scrap wood first Making a Cross CUTSee Ffeures44 .saw for the cut workFence Making a Miter CUT See F-agure43Fiouspersonalinjury 8LADE Angled Scale Making a Compound Bevel Miter CUT BEVELRiP. CUTSee g Making a Large Panel CUTNON-THROUGHCUT Guard Blade Removed Push Stick Making a Dado CUTTable Clampng Bracket Accessory Table UsageKnobbolt Nutbetween Adjustment Screws RearNUT ToinstallguidefencebracketsTo Install BIT and Throat Plate ToinstallrouterSee Ftgure55 Bladethroatplate Rmng Knife Blaie Large Small Wrench To Replace the BladeSee Figures57 Throm Plate BladeFraming Square Rivingblade Knife See Figures 60To Adjust the Miter Gauge HANDLEFig To Adjust the Bevel Locking LeverHEIGHT/BEVELADJUSTING Hanowheel Socket Hdsew Setscrew Blade ScrewsScrew ToaugnthemiterlockingclampsElevatingshaft Locker Bracket AssemblyGeneral LubricationCause SolutionBJadenot proper for rip cut Problem CauseCheck and adjustthe rip fence Reeharpenor set blade Lockinglever is not at full left positionCraftsman 10 in. Table SAW Model no FORlEG StandassemblyCraftsman 10 in. Table SAW Model NO, 3t5.2t8290 Parts List Figure aQty Parts ListDescription Qty Craftsman 10 in. Table SAW- Model noKey Part Number DeecdptlonScrew Craftsman t0 in. Table SAW Model no t5.218290 Craftsman 10 in. Table SAW Mooel no Figure F Miter Gauge AssemblyA181014601 Figureg Craftsman t0 in. Table SAW Model noKey Part Number DescdpUon Qty Description Parts List for Figure G411061704 Call anytime, day or night U.S.A. only Call anytime, day or night U.S.A. and Canada

315.21829 specifications

The Craftsman 315.21829 is a versatile and robust power tool designed for a variety of home improvement and woodworking tasks. Known for its reliability, this model is part of the Craftsman family, a brand that has built a reputation for offering user-friendly tools that provide high performance without compromising on safety and comfort.

One of the standout features of the Craftsman 315.21829 is its powerful motor, delivering ample horsepower to tackle demanding jobs. Whether you are cutting, sanding, or drilling, this tool ensures efficient operation and quick results. The design reflects an emphasis on power and precision, enabling users to achieve professional-quality finishes.

The ergonomic design of the Craftsman 315.21829 includes a comfortable grip, which reduces fatigue during extended use. This aspect is particularly important for both DIY enthusiasts and professionals who often spend long hours working on projects. The lightweight nature of the tool also contributes to its ease of use, making it suitable for a wide range of applications around the home and workshop.

A key technological feature of the Craftsman 315.21829 is its variable speed control, allowing users to adjust the tool's speed according to the specific requirements of the task at hand. This flexibility enhances control and precision, especially when working with delicate materials or intricate designs. The built-in safety features provide added peace of mind, ensuring that the tool operates under safe conditions at all times.

Another highlight is the compatibility with a wide range of accessories, which enhances the versatility of the Craftsman 315.21829. Users can easily switch between tasks, whether they are drilling holes, driving screws, or finishing surfaces. This adaptability makes it a valuable addition to any toolkit.

Overall, the Craftsman 315.21829 stands out for its combination of power, versatility, and user-friendly design. It caters to both seasoned professionals and DIY novices, enabling a wide array of projects to be completed with ease and precision. With its robust features and reliable performance, this tool continues to be a favorite in the realm of home improvement and woodworking.
Top Page Image Contents