Craftsman 315.28462 manual INDiCATOR, Slot Mounting the Table SAW Base to, Holelocking Knob

Page 16

iNDiCATOR

V SLOT

Fig. 6

Fig. 7

MOUNTING THE TABLE SAW BASE TO THE

LEG STAN D

See Figure 8.

[] Place the table saw base on the leg stand. Position the locking knob over the holes in the top of the leg stand.

[] Insert the screw on the locking knob into the hole and turn the locking knob clockwise to secure the table saw base to the leg stand.

[] Repeat with the other three locking knobs.

HOLELOCKING KNOB

Fig. 8

TO INSTALL THE HANDLE

See Figure 9.

[] Hold the nylon nut securely and turn the screw counter- clockwise to remove the nut completely. NOTE: Do not remove the screw from the handle.

[] Place the nylon nut into the recessed hole on the back of the height/bevel adjusting handwheel and hold in place.

[] Slide the handle and screw into the hole on the height/bevel adjusting handwheel.

[] Using a flathead screwdriver, turn the screw clockwise and tighten in place.

NUT

HANDLE

	SCREW
HEIGHT/BEVEL
ADJUSTING HANDWHEEL	Fig. 9
	Fig. 9

Image 16

Contents Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Before Making a CUT, be Sure ALL ADJUST= Ments are Secure Bladecoastsafter Being Turned OFFRemove ALL Fences and Auxiliary Tables Always USE Blade GUARD, SPREADER,NEVERstandorhaveanypartofyourbodyin line Hold the Workpiece Firmly Against the TablePage Symbol Signal ServiceYour nearest Authorized Service Center for repair LCAUTIONSpeed and Wiring Extension CordsCord Length Electrical ConnectionCutterhead planers and jointer planers FeatherboardGum Ripping or Rip CutProductspecifications Knowyourtablesaw See FigureSwitchin LOCKEDPOSiTiON OperatingcomponentsBlades ScrewdriverScrewdriver SquareThefollowingitemsareincludedwithyourtablesaw Unpacking Mounting HolesTo Assemble the LEG Stand See Figures 6Slot Mounting the Table SAW Base to INDiCATORHolelocking Knob To REMOVE/REPLACETHETHROATPLATE PlateBlade Wrench See Figures 13Pawl ANTI-KICKBACK Pawls Blade Guard LeverCorrect Verticaladjustment SET Screw SpreaderSpreader Rivingknife To Assemble the Sliding Table Assemlby See Figures 17Rear Screw ExtensionrodDust Dust BAGSee Figures 20 PushApplications Basic Operation of the Table SAWCauses of Kickback Avoiding KickbackHOW to Make a JIG for RIP Cutting Narrow Workpiece CuttingaidsPush Blocks Auxiliary Fence Stop JIG HandleHOW to Mount a Featherboard FeatherboardHowto Makea Featherboard Push PushTypesofcuts Crosscut BevelmitercutTo Changebladedepth GulletLocking Lever BevelTo USE the RIP Fence Blade Clamp Locking LeverFence Front Locking ScaleleverLock Miter GaugeHeelingparalleling the Blade to See Figures 36Switchswitch Onoff Switchin LockedpositionTo Make a Cross CUT See Figures 39Making a RIP CUT Making a Miter CUTMiter CUT Blade Straight Miter Gauge AngledMakinga Bevelcrosscut See Figures 43Bevelcrosscut Miter Gauge BladeangledBEVELRiP CUT RiP Fence Blade Angled Scale Making a Compound Bevel Miter CUTCompoundbevelmiter CUT Placelefthandon MiterHEIGHT/BEVEL Adjusting Handwheel Makinga Large Panel CUTMaking a NON-THROUGH CUT LargepanelcutBladeguard RemovedStick Making a Dado CUT DadocutArborblade See Figures 50Throat Plate Blade Wrench To Adjust the Miter Gauge Gaugebase Miter Gaugerod AdjustableLock 0 Adjustable Oadjustment ScrewLocking Lever General Maintenance To Check Alignment of the RIPFence to Blade BoltsSolution ProblemCause Problem Craftsman 10 in. Table SAW Model NumberKEY Part NO, Number DescriptionQTY KEY Part NO. NumberFigure B Parts List for Figure B Description QTYFigure C Parts List for Figure C Craftsman 10 in. Table SAW Model NumberFigure D DESCRiPTiON KEY Part NO. Number DescriptionNumber KEY Part NO. NumberParts List for Figure F KEY Part Number Description QTYPage @anag@