Craftsman 315.28462 manual

Page 6

Someofthefollowingsymbolsmaybeusedonthistool•Pleasestudythemandlearntheirmeaning•Properinter- pretationofthesesymbolswillallowyouto operatethetoolbetterandsafer•

A

@

O

@

@

V

A

mz

W

min

n o

[]

•../min

Safety Alert

Read Operator's Manual

Eye Protection

No Hands Symbol

Wet Conditions Alert

Volts

Amperes

Hertz

Watt

Minutes

Alternating Current

Direct Current

No Load Speed

Class II Construction

Per Minute

Indicates a potential personal injury hazard•

To reduce the risk of injury, user must read and understand operator's manual before using this product•

Always wear eye protection with side shields marked to comply with ANSI Z87.1.

Failure to keep your hands away from the blade will result in serious personal injury•

Do not expose to rain or use in damp locations•

Voltage

Current

Frequency (cycles per second)

Power

Time

Type of current

Type or a characteristic of current

Rotational speed, at no load

Double-insulated construction

Revolutions, strokes, surface speed, orbits etc., per minute

Image 6

Contents Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Remove ALL Fences and Auxiliary Tables Before Making a CUT, be Sure ALL ADJUST= Ments are SecureBladecoastsafter Being Turned OFF Always USE Blade GUARD, SPREADER,NEVERstandorhaveanypartofyourbodyin line Hold the Workpiece Firmly Against the TablePage Your nearest Authorized Service Center for repair Symbol SignalService LCAUTIONCord Length Speed and WiringExtension Cords Electrical ConnectionGum Cutterhead planers and jointer planersFeatherboard Ripping or Rip CutProductspecifications Knowyourtablesaw See FigureSwitchin LOCKEDPOSiTiON OperatingcomponentsScrewdriver BladesScrewdriver SquareThefollowingitemsareincludedwithyourtablesaw To Assemble the LEG Stand UnpackingMounting Holes See Figures 6INDiCATOR Slot Mounting the Table SAW Base toHolelocking Knob To REMOVE/REPLACETHETHROATPLATE PlatePawl Blade WrenchSee Figures 13 ANTI-KICKBACK Pawls Blade Guard LeverVerticaladjustment SET Screw Spreader CorrectSpreader Rivingknife Rear To Assemble the Sliding Table AssemlbySee Figures 17 Screw ExtensionrodSee Figures 20 DustDust BAG PushCauses of Kickback ApplicationsBasic Operation of the Table SAW Avoiding KickbackPush Blocks Auxiliary Fence HOW to Make a JIG for RIP Cutting Narrow WorkpieceCuttingaids Stop JIG HandleHowto Makea Featherboard HOW to Mount a FeatherboardFeatherboard Push PushTypesofcuts Crosscut BevelmitercutLocking Lever To ChangebladedepthGullet BevelFence Front To USE the RIP FenceBlade Clamp Locking Lever Locking ScaleleverLock Miter GaugeHeelingparalleling the Blade to See Figures 36To Make a Cross CUT Switchswitch OnoffSwitchin Lockedposition See Figures 39Miter CUT Blade Straight Making a RIP CUTMaking a Miter CUT Miter Gauge AngledBevelcrosscut Miter Gauge Makinga BevelcrosscutSee Figures 43 BladeangledCompoundbevelmiter CUT BEVELRiP CUT RiP FenceBlade Angled Scale Making a Compound Bevel Miter CUT Placelefthandon MiterMaking a NON-THROUGH CUT HEIGHT/BEVEL Adjusting HandwheelMakinga Large Panel CUT LargepanelcutStick Making a Dado CUT BladeguardRemoved DadocutSee Figures 50 ArborbladeThroat Plate Blade Wrench Lock 0 Adjustable To Adjust the Miter GaugeGaugebase Miter Gaugerod Adjustable Oadjustment ScrewFence to Blade Locking Lever General MaintenanceTo Check Alignment of the RIP BoltsProblem SolutionCause Problem Craftsman 10 in. Table SAW Model NumberQTY KEY Part NO, NumberDescription KEY Part NO. NumberFigure B Parts List for Figure B Description QTYFigure C Parts List for Figure C Craftsman 10 in. Table SAW Model NumberFigure D DESCRiPTiON KEY Part NO. Number DescriptionNumber KEY Part NO. NumberParts List for Figure F KEY Part Number Description QTYPage @anag@