Craftsman 315.28462 manual To Check Alignment of the RIP, Fence to Blade, Bolts, Lubrication

Page 38

TO CHECK THE

ALIGNMENT OF THE RIP

RiP FENCE

FENCE TO THE

BLADE

BLADE

 

See Figure 56.

 

 

[] Unplug the saw.

[] Raise the locking lever to permit the rip fence to be moved.

[] Place a framing square beside the blade and move the rip fence up to the square. Take the dimension on the rip scale.

[] Move the fence back and turn the framing square 180 ° to check the other side.

[]

If the two

dimensions are not the same,

loosen the

 

two bolts

on the fence and align it.

BOLTS

[]

Retighten

the two bolts.

 

[] Make two or three test cuts on scrap wood. If the cuts are not true, repeat the process.

LOCKING

LEVER

Fig. 5

A WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

A WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1 during product operation. If operation is dusty, also wear a dust mask.

A WARNING: Before performing any maintenance, make sure the tool is unplugged from the power supply and the switch is in the off ( O ) position. Failure to heed this warning could result in serious personal injury.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

A WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts.

Chemicals can damage, weaken, or destroy plastic which may result in serious personal injury.

[] Periodically check all clamps, nuts, bolts, and screws for tightness and condition. Make sure the throat plate is in good condition and in position.

[] Check the blade guard assembly.

[] To maintain the table surfaces, fence, and rails, periodically apply paste wax to them and buff to provide smooth functioning.

[] Protect the blade by cleaning out sawdust from underneath the table and in the blade teeth. Use a resin

solvent on the blade teeth.

[] Clean plastic parts only with a soft damp cloth. DO NOT use any aerosol or petroleum solvents.

LUBRICATION

All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrica- tion is required.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Remove ALL Fences and Auxiliary Tables Before Making a CUT, be Sure ALL ADJUST= Ments are SecureBladecoastsafter Being Turned OFF Always USE Blade GUARD, SPREADER,NEVERstandorhaveanypartofyourbodyin line Hold the Workpiece Firmly Against the TablePage Your nearest Authorized Service Center for repair Symbol SignalService LCAUTIONCord Length Speed and WiringExtension Cords Electrical ConnectionGum Cutterhead planers and jointer planersFeatherboard Ripping or Rip CutProductspecifications Knowyourtablesaw See FigureSwitchin LOCKEDPOSiTiON OperatingcomponentsScrewdriver BladesScrewdriver SquareThefollowingitemsareincludedwithyourtablesaw To Assemble the LEG Stand UnpackingMounting Holes See Figures 6Holelocking Knob INDiCATORSlot Mounting the Table SAW Base to To REMOVE/REPLACETHETHROATPLATE PlatePawl Blade WrenchSee Figures 13 ANTI-KICKBACK Pawls Blade Guard LeverSpreader Rivingknife Verticaladjustment SET Screw SpreaderCorrect Rear To Assemble the Sliding Table AssemlbySee Figures 17 Screw ExtensionrodSee Figures 20 DustDust BAG PushCauses of Kickback ApplicationsBasic Operation of the Table SAW Avoiding KickbackPush Blocks Auxiliary Fence HOW to Make a JIG for RIP Cutting Narrow WorkpieceCuttingaids Stop JIG HandleHowto Makea Featherboard HOW to Mount a FeatherboardFeatherboard Push PushTypesofcuts Crosscut BevelmitercutLocking Lever To ChangebladedepthGullet BevelFence Front To USE the RIP FenceBlade Clamp Locking Lever Locking ScaleleverLock Miter GaugeHeelingparalleling the Blade to See Figures 36To Make a Cross CUT Switchswitch OnoffSwitchin Lockedposition See Figures 39Miter CUT Blade Straight Making a RIP CUTMaking a Miter CUT Miter Gauge AngledBevelcrosscut Miter Gauge Makinga BevelcrosscutSee Figures 43 BladeangledCompoundbevelmiter CUT BEVELRiP CUT RiP FenceBlade Angled Scale Making a Compound Bevel Miter CUT Placelefthandon MiterMaking a NON-THROUGH CUT HEIGHT/BEVEL Adjusting HandwheelMakinga Large Panel CUT LargepanelcutStick Making a Dado CUT BladeguardRemoved DadocutThroat Plate Blade Wrench See Figures 50Arborblade Lock 0 Adjustable To Adjust the Miter GaugeGaugebase Miter Gaugerod Adjustable Oadjustment ScrewFence to Blade Locking Lever General MaintenanceTo Check Alignment of the RIP BoltsCause ProblemSolution Problem Craftsman 10 in. Table SAW Model NumberQTY KEY Part NO, NumberDescription KEY Part NO. NumberFigure B Parts List for Figure B Description QTYFigure C Parts List for Figure C Craftsman 10 in. Table SAW Model NumberFigure D DESCRiPTiON KEY Part NO. Number DescriptionNumber KEY Part NO. NumberParts List for Figure F KEY Part Number Description QTYPage @anag@
Top Page Image Contents