Craftsman 315.28462 manual To Assemble the Sliding Table Assemlby, See Figures 17, Rear

Page 20

TO ASSEMBLE THE SLIDING TABLE

ASSEMLBY

See Figures 17- 18.

To install s(iding table extension:

[] Locate the sliding table assembly.

[] Unlock the front and back table locking levers.

[] Insert sliding table assembly into table locking levers.

[] Push the table assembly until it rests against the saw table and is completely closed.

[] Install phillips head screw into hole at end of the rear extension rod to hold sliding table assembly into lock- ing levers.

[] Lock the front and back table locking levers. To install indicator:

[] Locate the indicator.

[] Slip the indicator in the slot on the front rail. Fit the top

slot in the indicator over the detent on the end plug and the bottom slot over the screw hole on the end plug.

[] Insert a screw into the bottom slot of the indicator, the hole in the end plug and the extension rod. Tighten se- curely, but do not overtighten. Overtighting may crush extension rod ends.

REAR

SCREW EXTENSIONROD

%

(

SLIDING

TABLE

ASSEMBLY

Fig. 17

DETENT

_SCREWHOLE

/INDICATOR

ENDPLUG

EXTENSION

ROD

TABLE

LOCKING

LEVER

SCREW Fig. 18

20

Image 20

Contents Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Before Making a CUT, be Sure ALL ADJUST= Ments are Secure Bladecoastsafter Being Turned OFFRemove ALL Fences and Auxiliary Tables Always USE Blade GUARD, SPREADER,NEVERstandorhaveanypartofyourbodyin line Hold the Workpiece Firmly Against the TablePage Symbol Signal ServiceYour nearest Authorized Service Center for repair LCAUTIONSpeed and Wiring Extension CordsCord Length Electrical ConnectionCutterhead planers and jointer planers FeatherboardGum Ripping or Rip CutProductspecifications Knowyourtablesaw See FigureSwitchin LOCKEDPOSiTiON OperatingcomponentsBlades ScrewdriverScrewdriver SquareThefollowingitemsareincludedwithyourtablesaw Unpacking Mounting HolesTo Assemble the LEG Stand See Figures 6Holelocking Knob INDiCATORSlot Mounting the Table SAW Base to To REMOVE/REPLACETHETHROATPLATE PlateBlade Wrench See Figures 13Pawl ANTI-KICKBACK Pawls Blade Guard LeverSpreader Rivingknife Verticaladjustment SET Screw SpreaderCorrect To Assemble the Sliding Table Assemlby See Figures 17Rear Screw ExtensionrodDust Dust BAGSee Figures 20 PushApplications Basic Operation of the Table SAWCauses of Kickback Avoiding KickbackHOW to Make a JIG for RIP Cutting Narrow Workpiece CuttingaidsPush Blocks Auxiliary Fence Stop JIG HandleHOW to Mount a Featherboard FeatherboardHowto Makea Featherboard Push PushTypesofcuts Crosscut BevelmitercutTo Changebladedepth GulletLocking Lever BevelTo USE the RIP Fence Blade Clamp Locking LeverFence Front Locking ScaleleverLock Miter GaugeHeelingparalleling the Blade to See Figures 36Switchswitch Onoff Switchin LockedpositionTo Make a Cross CUT See Figures 39Making a RIP CUT Making a Miter CUTMiter CUT Blade Straight Miter Gauge AngledMakinga Bevelcrosscut See Figures 43Bevelcrosscut Miter Gauge BladeangledBEVELRiP CUT RiP Fence Blade Angled Scale Making a Compound Bevel Miter CUTCompoundbevelmiter CUT Placelefthandon MiterHEIGHT/BEVEL Adjusting Handwheel Makinga Large Panel CUTMaking a NON-THROUGH CUT LargepanelcutBladeguard RemovedStick Making a Dado CUT DadocutThroat Plate Blade Wrench See Figures 50Arborblade To Adjust the Miter Gauge Gaugebase Miter Gaugerod AdjustableLock 0 Adjustable Oadjustment ScrewLocking Lever General Maintenance To Check Alignment of the RIPFence to Blade BoltsCause ProblemSolution Problem Craftsman 10 in. Table SAW Model NumberKEY Part NO, Number DescriptionQTY KEY Part NO. NumberFigure B Parts List for Figure B Description QTYFigure C Parts List for Figure C Craftsman 10 in. Table SAW Model NumberFigure D DESCRiPTiON KEY Part NO. Number DescriptionNumber KEY Part NO. NumberParts List for Figure F KEY Part Number Description QTYPage @anag@