Craftsman 315.28462 manual To REMOVE/REPLACETHETHROATPLATE, Plate

Page 17

TO REMOVE/REPLACETHETHROATPLATE

See Figure 10.

[] Lower the blade by turning the height/bevel adjusting handwheel counterclockwise.

[] To remove the throat plate, place your index finger in the hole and lift the front end pulling the throat plate out toward the front of the saw.

[] To reinstall the throat plate, slip the tab into the slot at the back of the saw and push down to secure in place.

PLATE

SPREADER/

RiViNG KNIFE

10

TO CHANGE BETWEEN A SPREADER AND A RIVING KNIFE

See Figure 11.

This saw is shipped with the spreader/riving knife placed in the non-through cutting or "down" position (riving knife position).

NOTE: The spreader/riving knife must be placed in the through cutting, or "up" position (spreader position), for all other cutting operations.

[] Unplug the saw.

To place in spreader position (or "up" position for all through cutting):

[] Remove the throat plate.

[] Raise the saw blade by turning the height/bevel adjust- ing handwheel clockwise.

[] Unlock the release lever by pulling it up.

[] Grasp the spreader and pull it towards the right side of the saw to release the spreader from the spring-loaded riving clamp.

[] Pull the spreader up until the internal pins are engaged and the spreader is above the saw blade.

[] Lock the release lever by pushing the lever down.

[] Reinstall the throat plate.

To place in riving knife position (or "down" position for all non-through cutting):

[] Remove the throat plate.

[] Raise the saw blade by turning the height/bevel adjust- ing handwheel clockwise.

[] Unlock the release lever by pulling it up.

[] Push the riving knife down until it is below the saw blade.

[] Lock the release lever by pushing the lever down.

[] Reinstall the throat plate.

_(URELEASE

LEVER

NLOCKED)

IN "UP" POSITIONFORTHROUGHCUTTING

RELEASE

LEVER

IN "DOWN" POSITIONFOR NON-THROUGHCUTTING

Fig. 11

17

Image 17
Contents Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Bladecoastsafter Being Turned OFF Before Making a CUT, be Sure ALL ADJUST= Ments are SecureRemove ALL Fences and Auxiliary Tables Always USE Blade GUARD, SPREADER,Hold the Workpiece Firmly Against the Table NEVERstandorhaveanypartofyourbodyin linePage Service Symbol SignalYour nearest Authorized Service Center for repair LCAUTIONExtension Cords Speed and WiringCord Length Electrical ConnectionFeatherboard Cutterhead planers and jointer planersGum Ripping or Rip CutProductspecifications See Figure KnowyourtablesawOperatingcomponents Switchin LOCKEDPOSiTiONScrewdriver BladesScrewdriver SquareThefollowingitemsareincludedwithyourtablesaw Mounting Holes UnpackingTo Assemble the LEG Stand See Figures 6Holelocking Knob INDiCATORSlot Mounting the Table SAW Base to Plate To REMOVE/REPLACETHETHROATPLATESee Figures 13 Blade WrenchPawl ANTI-KICKBACK Pawls Blade Guard LeverSpreader Rivingknife Verticaladjustment SET Screw SpreaderCorrect See Figures 17 To Assemble the Sliding Table AssemlbyRear Screw ExtensionrodDust BAG DustSee Figures 20 PushBasic Operation of the Table SAW ApplicationsCauses of Kickback Avoiding KickbackCuttingaids HOW to Make a JIG for RIP Cutting Narrow WorkpiecePush Blocks Auxiliary Fence Stop JIG HandleFeatherboard HOW to Mount a FeatherboardHowto Makea Featherboard Push PushCrosscut Bevelmitercut TypesofcutsGullet To ChangebladedepthLocking Lever BevelBlade Clamp Locking Lever To USE the RIP FenceFence Front Locking ScaleleverMiter Gauge LockSee Figures 36 Heelingparalleling the Blade toSwitchin Lockedposition Switchswitch OnoffTo Make a Cross CUT See Figures 39Making a Miter CUT Making a RIP CUTMiter CUT Blade Straight Miter Gauge AngledSee Figures 43 Makinga BevelcrosscutBevelcrosscut Miter Gauge BladeangledBlade Angled Scale Making a Compound Bevel Miter CUT BEVELRiP CUT RiP FenceCompoundbevelmiter CUT Placelefthandon MiterMakinga Large Panel CUT HEIGHT/BEVEL Adjusting HandwheelMaking a NON-THROUGH CUT LargepanelcutRemoved BladeguardStick Making a Dado CUT DadocutThroat Plate Blade Wrench See Figures 50Arborblade Gaugebase Miter Gaugerod Adjustable To Adjust the Miter GaugeLock 0 Adjustable Oadjustment ScrewTo Check Alignment of the RIP Locking Lever General MaintenanceFence to Blade BoltsCause ProblemSolution Problem 10 in. Table SAW Model Number CraftsmanDescription KEY Part NO, NumberQTY KEY Part NO. NumberFigure B Description QTY Parts List for Figure BFigure C Craftsman 10 in. Table SAW Model Number Parts List for Figure CFigure D KEY Part NO. Number Description DESCRiPTiONKEY Part NO. Number NumberKEY Part Number Description QTY Parts List for Figure FPage @anag@