Craftsman 315.28462 manual Blades, Screwdriver, Square, Clamps

Page 13

BLADES

 

 

 

A WARNING:

 

 

 

For maximum

performance, it is recommended

that you

Do not use blades rated

less than

the

use the 36-tooth, 10 in. carbide-tipped combination blade

speed

of this

tool. Failure to heed this

warning

could

provided

with

your saw. Additional blade styles

of the

result

in personal injury.

 

 

same high quality are available for specific operations

 

 

 

 

 

such as ripping. Your local dealer can provide you with

 

 

 

 

 

complete

information.

 

 

 

 

 

 

Kerf width must be within the limits stamped on the spreader/riving knife.

_The following tools (not included or drawn to scale) are needed for assembly and making adjustments:

SCREWDRIVER

SCREWDRIVER

COMBiNATiON

SQUARE

U AND10mmSOCKET

C-CLAMPS

Fig. 4

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Bladecoastsafter Being Turned OFF Before Making a CUT, be Sure ALL ADJUST= Ments are SecureRemove ALL Fences and Auxiliary Tables Always USE Blade GUARD, SPREADER,Hold the Workpiece Firmly Against the Table NEVERstandorhaveanypartofyourbodyin linePage Service Symbol SignalYour nearest Authorized Service Center for repair LCAUTIONExtension Cords Speed and WiringCord Length Electrical ConnectionFeatherboard Cutterhead planers and jointer planersGum Ripping or Rip CutProductspecifications See Figure KnowyourtablesawOperatingcomponents Switchin LOCKEDPOSiTiONScrewdriver BladesScrewdriver SquareThefollowingitemsareincludedwithyourtablesaw Mounting Holes UnpackingTo Assemble the LEG Stand See Figures 6Slot Mounting the Table SAW Base to INDiCATORHolelocking Knob Plate To REMOVE/REPLACETHETHROATPLATESee Figures 13 Blade WrenchPawl ANTI-KICKBACK Pawls Blade Guard LeverCorrect Verticaladjustment SET Screw SpreaderSpreader Rivingknife See Figures 17 To Assemble the Sliding Table AssemlbyRear Screw ExtensionrodDust BAG DustSee Figures 20 PushBasic Operation of the Table SAW ApplicationsCauses of Kickback Avoiding KickbackCuttingaids HOW to Make a JIG for RIP Cutting Narrow WorkpiecePush Blocks Auxiliary Fence Stop JIG HandleFeatherboard HOW to Mount a FeatherboardHowto Makea Featherboard Push PushCrosscut Bevelmitercut TypesofcutsGullet To ChangebladedepthLocking Lever BevelBlade Clamp Locking Lever To USE the RIP FenceFence Front Locking ScaleleverMiter Gauge LockSee Figures 36 Heelingparalleling the Blade toSwitchin Lockedposition Switchswitch OnoffTo Make a Cross CUT See Figures 39Making a Miter CUT Making a RIP CUTMiter CUT Blade Straight Miter Gauge AngledSee Figures 43 Makinga BevelcrosscutBevelcrosscut Miter Gauge BladeangledBlade Angled Scale Making a Compound Bevel Miter CUT BEVELRiP CUT RiP FenceCompoundbevelmiter CUT Placelefthandon MiterMakinga Large Panel CUT HEIGHT/BEVEL Adjusting HandwheelMaking a NON-THROUGH CUT LargepanelcutRemoved BladeguardStick Making a Dado CUT DadocutArborblade See Figures 50Throat Plate Blade Wrench Gaugebase Miter Gaugerod Adjustable To Adjust the Miter GaugeLock 0 Adjustable Oadjustment ScrewTo Check Alignment of the RIP Locking Lever General MaintenanceFence to Blade BoltsSolution ProblemCause Problem 10 in. Table SAW Model Number CraftsmanDescription KEY Part NO, NumberQTY KEY Part NO. NumberFigure B Description QTY Parts List for Figure BFigure C Craftsman 10 in. Table SAW Model Number Parts List for Figure CFigure D KEY Part NO. Number Description DESCRiPTiONKEY Part NO. Number NumberKEY Part Number Description QTY Parts List for Figure FPage @anag@
Top Page Image Contents