Craftsman 315.28462 manual Problem, Cause, Solution

Page 39

Thefollowingrecommendedaccessoriesarecurrentlyavailableatretailstores:

089037008711 DadoThroatPlatewithSpecialWasher

_I_, WARNING:Currentattachmentsandaccessoriesavailablefor usewiththistool arelistedabove.Donotuse

anyattachmentsoraccessoriesnotrecommendedbythemanufacturerofthistool.Theuseof attachmentsor accessoriesnotrecommendedcanresultin seriouspersonalinjury.

PROBLEM

Excess vibration.

Rip fence does not move smoothly.

Rip fence does not lock at rear.

Cutting binds or burns work.

Wood edges away from rip fence when ripping.

CAUSE

Blade is out of balance.

Blade is damaged.

Saw is not mounted securely.

Work surface is uneven.

Blade is warped.

Rip fence not mounted correctly.

Rails are dirty or sticky.

Clamp screw is out of adjustment.

Clamp screw is out of adjustment.

Blade is dull.

Blade is heeling.

Work is fed too fast.

Rip fence is misaligned.

Wood is warped.

Spreader is out of alignment.

Blade not properly sharpened or set.

SOLUTION}

Replace blade.

Replace blade.

Tighten all hardware.

Reposition on flat surface.

Adjust legs of optional stand.

Check saw blade installation. Replace blade if necessary.

Remount the rip fence.

Clean and wax rails.

Adjust clamp screw counterclockwise.

Adjust clamp screw clockwise.

Replace or sharpen blade.

See page 29 on "Heeling the Blade".

Slow the feed rate.

Align the rip fence.

Replace the wood. Always cut with convex side to table surface.

See "To check and align the spreader/riving knife and saw blade" in the Assembly section.

Resharpen or set blade.

39

Image 39

Contents Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Always USE Blade GUARD, SPREADER, Before Making a CUT, be Sure ALL ADJUST= Ments are SecureBladecoastsafter Being Turned OFF Remove ALL Fences and Auxiliary TablesHold the Workpiece Firmly Against the Table NEVERstandorhaveanypartofyourbodyin linePage LCAUTION Symbol SignalService Your nearest Authorized Service Center for repairElectrical Connection Speed and WiringExtension Cords Cord LengthRipping or Rip Cut Cutterhead planers and jointer planersFeatherboard GumProductspecifications See Figure KnowyourtablesawOperatingcomponents Switchin LOCKEDPOSiTiONSquare BladesScrewdriver ScrewdriverThefollowingitemsareincludedwithyourtablesaw See Figures 6 UnpackingMounting Holes To Assemble the LEG StandINDiCATOR Slot Mounting the Table SAW Base toHolelocking Knob Plate To REMOVE/REPLACETHETHROATPLATEANTI-KICKBACK Pawls Blade Guard Lever Blade WrenchSee Figures 13 PawlVerticaladjustment SET Screw Spreader CorrectSpreader Rivingknife Screw Extensionrod To Assemble the Sliding Table AssemlbySee Figures 17 RearPush DustDust BAG See Figures 20Avoiding Kickback ApplicationsBasic Operation of the Table SAW Causes of KickbackStop JIG Handle HOW to Make a JIG for RIP Cutting Narrow WorkpieceCuttingaids Push Blocks Auxiliary FencePush Push HOW to Mount a FeatherboardFeatherboard Howto Makea FeatherboardCrosscut Bevelmitercut TypesofcutsBevel To ChangebladedepthGullet Locking LeverLocking Scalelever To USE the RIP FenceBlade Clamp Locking Lever Fence FrontMiter Gauge LockSee Figures 36 Heelingparalleling the Blade toSee Figures 39 Switchswitch OnoffSwitchin Lockedposition To Make a Cross CUTMiter Gauge Angled Making a RIP CUTMaking a Miter CUT Miter CUT Blade StraightBladeangled Makinga BevelcrosscutSee Figures 43 Bevelcrosscut Miter GaugePlacelefthandon Miter BEVELRiP CUT RiP FenceBlade Angled Scale Making a Compound Bevel Miter CUT Compoundbevelmiter CUTLargepanelcut HEIGHT/BEVEL Adjusting HandwheelMakinga Large Panel CUT Making a NON-THROUGH CUTDadocut BladeguardRemoved Stick Making a Dado CUTSee Figures 50 ArborbladeThroat Plate Blade Wrench Oadjustment Screw To Adjust the Miter GaugeGaugebase Miter Gaugerod Adjustable Lock 0 AdjustableBolts Locking Lever General MaintenanceTo Check Alignment of the RIP Fence to BladeProblem SolutionCause Problem 10 in. Table SAW Model Number CraftsmanKEY Part NO. Number KEY Part NO, NumberDescription QTYFigure B Description QTY Parts List for Figure BFigure C Craftsman 10 in. Table SAW Model Number Parts List for Figure CFigure D KEY Part NO. Number Description DESCRiPTiONKEY Part NO. Number NumberKEY Part Number Description QTY Parts List for Figure FPage @anag@