Craftsman 113.24181 Beve L Crosscutting, Compound Miter Cutting, Endanger Your Hands

Page 19

1.NEVERUSETHERIPFENCEASA LENGTHSTOP BECAUSETHE CUTOFFPIECECOULDBIND BETWEENTHEFENCEANDTHEBLADECAUSING A KICKBACK.

2.Whenmakingrepetitivecutsshorterthan6in.,clamp blockof wood3 in. longto thetabletoactasalength stop.

CAUTION: When clamping the block, make sure that the end of the block is well in front of the sawblade. Be

sure it is clamped securely.

3. Slide the workpiece along the miter gauge until it touches the block ... hold it securely or clamp it with the Hold-Down Clamp (Optional Accessory).

4.Make the cut ... pull the workpiece back ... push the cut off piece off the table with a long push stick ...

DO NOT ATTEMPT TO PICK IT UP AS THIS COULD

ENDANGER YOUR HANDS.

MITER CUTTING

MITER CUTTING is known as cutting wood at an angle other than 90 ° with the edge of the wood. Follow the same procedure as you would for crosscutting.

Adjust the miter gauge to the desired angle, and lock it.

The miter gauge may be used in either of the grooves in the table.

When using the miter gauge in the LEFT Hand groove, hold

the workpiece firmly against the miter gauge head with your left hand, and grip the lock handle with your right. When using the RIGHT hand groove, hold the workpiece

with your right hand and the Iockhandle with your left hand.

Use the Hold-Down Clamp (Optional Accessory) on the miter gauge for greater accuracy.

BEVE L CROSSCUTTING

BEVEL CROSSCUTTING is the same as crosscutting except that the wood is also cut at an angle ... other than g0 ° with the flat side of the wood.

Adjust the blade to the desired angle.

Use the Miter Gauge in the groove to the RIGHT of the blade. It cannot be used in the groove to the LEFT because

the blade guard will interfere. Hold the workpiece with your right hand and the Iockhandle with your left hand.

Use the AUXILIARY FENCE/WORK SUPPORT for

additional support of the workpiece.

Lay it across the guide bars to support the workpiece as near to the end as possible.

Use the Hold-Down Clamp (Optional Accessory) on the miter gauge for greater accuracy.

COMPOUND MITER CUTTING

COMPOUND MITER CUTTING is a combination of miter

cutting and bevel crosscutting. The cut is made at an angle

other than 90 ° to both the edge and the flat side of the wood.

Adjust the miter gauge and the blade to the desired angle

... Make sure miter gauge is locked.

1

1

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 113.24181 Model noFor Power Tools Protection EYES, HANDS, FACE, EARS, Body For Table SawsLocation KickbacksWear Your Motor Specfications Electrical RequirementsContents Unpacking and Checking Contents Turn the saw upside down AssemblyNUTS, HEX Attaching Table Extensions Checking Blade Squareness to TableNot Tighten Insert Installing RIP Fence Guide BarsHoldrodwithonehandandwitha 7/16 in. wrench or Aligning RIP Fence Rip fence must be Parallel with the sawblade Installing Blade GuardHEX Screvs Lock Setscrew Wrenches Space Eqljal to Approx Thicknesses of Paper Kerf WoodParallel ANTI-KICKBACK PawlsEtting to RN OW Your SAW ON-OFF SwitchAuxiliary Facing Limit StopsLeft RightEXACT-I-CUT Removing and Installing SawbladeRemove insert Push Stick and Push Block OperationWork Helpers CROSSCUTTING, Miter CUTTING, Bevel CuttingGroove CrosscuttingRepetitive Cutting ManufacturingEndanger Your Hands Miter CuttingBeve L Crosscutting Compound Miter CuttingKickback Bevel RippingPush Block Do not Back UP Reverse Feeding While ResawingCutti NG PAN ELS RabbetingMiter Gauge AdjustmentsTeeth Blade TILT, or Squareness Blade to TableStop Screw Elevation Lock MaintenanceOutlet Before Maintaining or Lubricating Your SAW 3218 Miter GuageWorm and Teeth 22201Trouble Probable Cause Outlet Before TroubleshootingOr fails to come up TroubleProbable Cause Remedy20m Parts List for Craftsman 12-INCH Motorized Table SAWParts List for Craftsman 12-INCHMOTORIZED Table SAW Model Number 50A 2852 Parts LiST for Craftsman 12-INCH Motorized Table SAW 62581 Fence Assembly Box Assembly Control w/Nameplate Parts List for Raftsman 12-INCHMOTORIZED Table SAWRepair Service is Available AT Your Nearest Sears Store Complete Motor AssemblySTD See Wiring DIAGRAM,62325 Miter Gauge Assembly 62594 Guard Assembly Parts List for Craftsman 12-! NCH Motorized Table SAW62589 Table Extension Sears TAB LE SAW Service
Top Page Image Contents