2
ELEVATION CRANK . . . elevates or IoweFs the blade.
Turn clockwise to elevate ... counterclockwise to lower.
3ELEVATION LOCK . •. locks the blade at the desired
height. PUSH in to LOCK... PULL out to unlock.
4 TILT |
| CRANK | ... |
| tilts |
| the blade for bevel cutting. | |||||||||
Turn | clockwise | to | tilt | toward | left | ... | counterclockwise | |||||||||
to | tilt |
| toward | right. |
|
|
|
|
|
|
|
|
|
| ||
When |
| the | blade | is | tilted | to the LEFT as far as it will go, | ||||||||||
.it | should | be | at | 45 ° | to | the | table | and | the | bevel | pointer | |||||
should |
| point | 45 ° . |
|
|
|
|
|
|
|
|
|
| |||
NOTE: | There | are | LIMIT |
| STOPS | inside | the | saw | which | |||||||
prevent | the | blade | from | tilting | beyond | 45 ° to | the | LEFT | ||||||||
and | 90 ° | to | the | RIGHT. | (See | "Adjustments" |
| section | ||||||||
"Blade | Tilt, | or | Squareness | of | Blade to | Table")• |
|
| ||||||||
Select a suitable piece of smooth straight wood ...
drill two holes through it and attach it with smalt
screws and nuts. The nuts go inside of the miter gauge. Or drill 1/4 in. holes all the way through the head. Then
you can attach the facing with wood screws.
NOTE: When bevel crosscutting, attach facing so that it
extends to the right of the miter gauge and use the miter gauge in the groove to the right of the blade.
AUXILIARY FACING
NOTE: WHEN BEVEL CROSSCUTTING,.
5TILT LOCK KNOB ... locks the blade in the desired tilt position. Turn it to the left to unlock ... to the right to lock.
6RiP FENCE ... is locked in place by tightening the lock handle. To move the fence, loosen the handle and grasp the fence with one hand at the front.
Holes are provided in the rip fence for attaching a wood facing when using the dado head, or molding head. Select a piece of smooth straight wood approx. 3/4 in. thick and the same size as the rip fence.
Attach it to the fence with three Round Head #10 Wood Screws 2 in. long. To remove the facing, loosen the screws, slide the facing forward and pull the screws through the round holes.
WOOD FACING
\
STOP PIN | 45 ° HOLE | |
FOR STOP PIN | ||
|
8 BLADEGUARD must always be in place and working
properly for all
whereby the blade cuts completely through the workpiece.
To remove the guard for special operations, loosen the
thumbscrew and slide the guard off of the rod. DO NOT DISTURB THE SETTING OF THE ROD.
When replacing the guard, make sure the PIN in the rod engages with the NOTCH in the spreader support. Make
sure thumbscrew is tightened securely.
9TABLE INSERT is removable for removing or installing blades or other cutting tools.
(_2D
ROUND _EAD //_
#10 WOOD SCREWS
7 MITER GAUGE ... head is locked in position for
crosscutting or mitering by tightening the lock handle.
ALWAYS LOCK IT SECURELY WHEN IN USE.
There are two holes for the stop pin at the 45 degree
right and left positions for conveniently setting the Miter Gauge to cut miters.
NOTE: The holes for the stop pin and the graduations
are manufactured to very close tolerances which
provide accuracy for average woodworking. In some cases where extreme accuracy is required, when making
angle cuts, for example, make a trial cut and then recheck it.
If necessary, the miter gauge head can then be swiveled slightly to compensate and then locked.
Holes are provided in the miter gauge for attaching an
AUXILIARY FACING to make it easier to cut long pieces.
WARNING: FOR YOUR OWN SAFETY, TURN
SWITCH "OFF" AND REMOVE PLUG FROM
POWER SOURCE OUTLET BEFORE REMOVING INSERT.
A.Lower the blade below the table surface.
B.Raise blade guard.
C.Lift insert from front end, and pull toward front of saw.
NEVER OPERATE THE SAW WITHOUT THE PROPER INSERT IN PLACE. USE THE SAW BLADE
INSERT WHEN SAWING . . . USE THE
COMBINATION DADO MOLDING INSERT WHEN DADOING OR MOLDING.
15