Craftsman 113.24181 Space Eqljal to Approx Thicknesses of Paper Kerf Wood, Parallel, Fence

Page 13

3.SHdesupportontoSUPPORTRODuntilPINinrodfits into notchin support... insertTHUMBSCREWand tightenit.

4.LoosensetscrewinendofSPREADERBARusing5/32

in.setscrewwrench.

5.Slideguardto rightuntilendof rodisevenwithbar.

6.Makesurebladeissquareto tableandraisedashighas

it will go.

SUPPORT ROD

! I SPREADER BAR ,_

SPACE EQLJAL TO APPROX.

8 THICKNESSES OF PAPER KERF WOOD

IMPORTANT:	The SPREADER	must always	be
PARALLEL	to the sawblade and	in the MIDDLE of	the
cut (KERF) made by the sawblade.

NOTE: The spreader is thinner than the width of the

KERF by approximately sixteen thicknesses of paper,

SPACE EQUAL	TO APPROX.	LOOKING	DOWN ON SAW
8 THICKNESSES	OF PAPER

7.Make seven folds in a small piece (10 x 10 in.) of ordinary NEWSPAPER making eight thicknesses.

The folded paper will be used as a "spacing gauge".

8.Place RIP FENCE on table ... CAREFULLY move it against blade so that it is parallel to the blade, and just

TOUCHES tips of saw teeth . .. tighten RIP FENCE LOCK KNOB.

9. Lift	up	both	ANTI-KICKBACK		PAWLS...		insert		one
of the		SETSCREW		WRENCHES	in the	notches		to	hold
the pawls out of the way.
10. Insert		folded	paper	between SPREADER			and	FENCE
...	hold spreader			flat against	fence..,	tighten		screws.

11.Now tighten setscrew in end of spreader bar.

12.To remove blade guard, loosen thumb screw and slide guard off of SUPPORT ROD.

NOTE: Move fence away from spreader ... to see if spreader remains SQUARE with table.

If it is not square with table, the SPREADER BAR must be adjusted.

A.Loosen 2 clamping screws, using a 1/2 in. wrench.

B.Rotate bar until spreader is square with table.

C.Check alignment of spreader with blade and readjust, if necessary.

FOLDED PAPER

7,/16 IN. WRENCH

, - _sCR[WS _/_----_ _PP-'-r--

___

SPREAD E_R/_'_

_

Image 13

Contents 113.24181 Model noFor Power Tools Location For Table SawsKickbacks Protection EYES, HANDS, FACE, EARS, BodyWear Your Motor Specfications Electrical RequirementsContents Unpacking and Checking Contents Turn the saw upside down AssemblyNUTS, HEX Attaching Table Extensions Checking Blade Squareness to TableNot Tighten Insert Installing RIP Fence Guide BarsHoldrodwithonehandandwitha 7/16 in. wrench or Aligning RIP Fence Rip fence must be Parallel with the sawblade Installing Blade GuardHEX Screvs Lock Parallel Space Eqljal to Approx Thicknesses of Paper Kerf WoodANTI-KICKBACK Pawls Setscrew WrenchesEtting to RN OW Your SAW ON-OFF SwitchLeft Limit StopsRight Auxiliary FacingEXACT-I-CUT Removing and Installing SawbladeRemove insert Work Helpers OperationCROSSCUTTING, Miter CUTTING, Bevel Cutting Push Stick and Push BlockRepetitive Cutting CrosscuttingManufacturing GrooveBeve L Crosscutting Miter CuttingCompound Miter Cutting Endanger Your HandsKickback Bevel RippingPush Block Cutti NG PAN ELS ResawingRabbeting Do not Back UP Reverse Feeding WhileMiter Gauge AdjustmentsTeeth Blade TILT, or Squareness Blade to TableStop Screw Elevation Lock MaintenanceOutlet Before Maintaining or Lubricating Your SAW Worm and Teeth Miter Guage22201 3218Trouble Probable Cause Outlet Before TroubleshootingProbable Cause TroubleRemedy Or fails to come up20m Parts List for Craftsman 12-INCH Motorized Table SAWParts List for Craftsman 12-INCHMOTORIZED Table SAW Model Number 50A 2852 Parts LiST for Craftsman 12-INCH Motorized Table SAW 62581 Fence Assembly Repair Service is Available AT Your Nearest Sears Store Parts List for Raftsman 12-INCHMOTORIZED Table SAWComplete Motor Assembly Box Assembly Control w/NameplateSTD See Wiring DIAGRAM,62325 Miter Gauge Assembly 62594 Guard Assembly Parts List for Craftsman 12-! NCH Motorized Table SAW62589 Table Extension Sears TAB LE SAW Service