Model 5000A/5000AL/5000AP

Page No 1

1/2" Pistol Grip Twin Hammer

Impact Wrenches

Form # ZCE547 Date 2006June7/A

Operator Instructions

Important

Includes – Foreseen Use, Work Stations, Putting Into Service,

Read these instructions carefully before installing, operating,

servicing or repairing this tool. Keep these instructions in a safe

Operating, Dismantling, Assembly and Safety Rules.

accessible place.

Manufacturer/Supplier

Product Type

RPM

8,000

Sioux Tools, Inc.

1/2" Pistol Grip Twin

Cycles Per Min.

250 Snap-on Drive

Hammer Impact Wrenches

P.O. Box 1596

Model No/Nos

Serial No.

Murphy, NC 28906

5000A

Std. Anvil

U.S.A.

5000AL 2" Ext. Anvil

Tel No. 828-835-9765

Fax No. 828-835-9685

5000AP Std. Pin Anvil

Product Net Weight

Recommended Use Of

Recommended Hose Bore

Recommended Max.

6.00 (Std)

6.10 (2") lbs

Balancer Or Support

Size – Minimum

Hose Length

2.75 (Std)

2.77 (2") Kg

3/8 ins

10 mm

30 Ft

10 M

Air Pressure

Noise Level: Sound Pressure Level 97.0 dB(A)

Sound Power Level

108.0 dB(A)

Recommended Working

6.2

bar

PSI

Test Method: Tested in accordance with Pneurop

Maximum

6.2

bar

PSI

test code PN8NTC1 and ISO Standard 3744

SAFETY MESSAGES

WARNING

Vibration Level

Meters / Sec2

Personal Safety Equipment

Always Read Instructions

Use – Safety Glasses

YES

Before Using Power Tools

Test Method: Tested in accordance with ISO

Always Wear Safety

Use – Safety Gloves

Goggles

standards 8662 Parts 1 & 7

Use – Safety Boots

Wear Hearing Protection

Use – Breathing Masks

Avoid Prolonged Exposure

Use – Ear Protectors

YES

To Vibration

Safety rules when using 5000A/5000AL/5000AP

footing and/or position and grip the tool sufficiently only to

Impact Wrenches

overcome any reaction forces that may result from the tool doing

– Use only impact sockets and extensions, universal joints, etc. rated

work. Do not overgrip.

– Use only correct spare parts for maintenance and repair. Do not

as being suitable for use with impact wrenches.

improvise or make temporary repairs. Major servicing and repairs

– Prolonged exposure to vibration may cause injury.

should only be carried out by persons trained to do so.

– Read all instructions before using this tool. All operators must be

– Do not lock, tape, wire, etc. the ‘On/Off’ valve in ‘On’ position. The

fully trained in its use and aware of these safety rules.

trigger/lever, etc. must always be free to return to the ‘Off’ position

– Do not exceed the maximum working air pressure.

when released.

– Use personal protection equipment as recommended.

– Always shut off the air supply to the tool and press the ‘On/Off’

– Some dust created by power sanding, sawing, grinding, drilling,

valve to exhaust the air from the feed hose before fitting, removing

and other construction activities contains

or adjusting the working attachment fitted to the tool.

chemicals known to cause cancer, birth defects and other

– Before using the tool, make sure that a shut off device has been

reproductive harm.

fitted to the air supply line and the position is known and easily

– Use only compressed air at the recommended conditions.

accessible so that the air supply to the tool can be shut off in an

– If the tool appears to malfunction, remove from use immediately

emergency.

and

– Check hose and fittings regularly for wear.

arrange for service and repair. If it is not

practical to remove tool from service, then

shut off the air supply to the tool and write or

have written a warning note and attach it to

the tool.

– If tool is to be used with a balancer or other

suspension device, ensure that the tool is

firmly attached to the suspension/support

device.

– When operating the tool, always keep the

body and particularly the hands away from

the working attachment fixed to the tool.

– The tool is not electrically insulated. Never

use the tool if there is any chance of coming

into contact with live electricity.

– Always when using the tool, adopt a firm

Recommended Air Supply System

Figure 1