Multi-Tech Systems MMV1600 H4 menu is as follows, H5 menu is as follows, H6 menu is as follows

Page 46

$DSUACL - SELECTS CLOCKING FOR INTERNAL DSU LINK A. $DSUBCL - SELECTS CLOCKING FOR INTERNAL DSU LINK B. $DSUASP - SELECTS SPEED FOR INTERNAL DSU LINK A. $DSUBSP - SELECTS SPEED FOR INTERNAL DSU LINK B.

EXTERNAL DSU/MODEM

$MUXACL - SELECTS CLOCKING WHEN USING EXTERNAL DSU/MODEM PORT A. $MUXBCL - SELECTS CLOCKING FROM EXTERNAL SYNC DEVICE ON PORT B. $MUXASP - SPEED OF THE CLOCK IF SUPPLIED BY THE MULTIPLEXER PORT A. $MUXBSP - SPEED OF THE CLOCK IF SUPPLIED BY THE MULTIPLEXER PORT B. $MUXB - SELECTS PORT B AS SYNC DATA CHANNEL OR COMPOSITE LINK.

FOR HELP ON A SPECIFIC COMMAND, ENTER "ATH" FOLLOWED BY THE COMMAND LETTER.

EXAMPLE: ATH$DSUACL "ENTER"

The H4 menu is as follows:

ADDITIONAL COMPOSITE LINK COMMANDS

#C	- CLEAR COMPOSITE STATISTICS
$F - LOAD FACTORY DEFAULTS FOR DSU AND ISCC
#FT	- FLUSH TIMER VALUE
$L - LIST CONFIGURATION OF PORT A & B
#L	- LIST COMPOSITE LINK SETTINGS
#RB	- SET AUTO REPORTING BAUD RATE
#RT	- SET AUTO REPORTING TIME INTERVAL
#RXT - PROGRAMMABLE RETRANSMIT TIMER
#S	- COMPOSITE LINK STATISTICS
#SL	- STATUS OF FRONT PANEL LEDS

FOR HELP ON A SPECIFIC COMMAND, ENTER “ATH” FOLLOWED BY A COMMAND LETTER.

The H5 menu is as follows:

MISCELLANEOUS COMMANDS

I- ID CODE

#MA	- MODEM ACCESS FOR COMMAND MODEM
#RA	- REMOTE ACCESS FOR COMMAND MODEM
&T	-	TEST MODES
&W	-	SAVE PARAMETERS "WRITE TO MEMORY"

Z- RESET MULTIMUX

FOR HELP ON A SPECIFIC COMMAND, ENTER “ATH” FOLLOWED BY A COMMAND LETTER.

The H6 menu is as follows:

VOICE/FAX CHANNEL COMMANDS

VL	- LIST THE VOICE/FAX CHANNEL PARAMETERS
V(1/2)Z	-	RESET VOICE/FAX CHANNEL
V(1/2)DR	- VOICE/FAX CHANNEL DIGITIZING RATE
V(1/2)DC	-	VOICE/FAX DESTINATION CHANNEL
V(1/2)DN	-	VOICE/FAX DESTINATION NODE
V(1/2)ML	- LINK THE VOICE/FAX CHANNEL WILL COMMUNICATE OVER
V(1/2)OL	- VOICE/FAX CHANNEL OUTPUT LEVEL ATTENTUATION
V(1/2)IL	- VOICE/FAX CHANNEL INPUT LEVEL GAIN
V(1/2)SS	- VOICE/FAX CHANNEL SILENCE SUPPRESSION

COMMAND EXAMPLE 1: ATV1DN2 - SETS THE DESTINATION NODE OF CHANNEL 1 TO 2.

FOR HELP ON A SPECIFIC COMMAND, ENTER “ATH” FOLLOWED BY A COMMAND LETTER.

The H7 menu is as follows:

ADDITIONAL VOICE/FAX CHANNEL COMMANDS

V(1/2)LI	-	VOICE/FAX CHANNEL LOCAL INTERFACE
V(1/2)RI	-	VOICE/FAX CHANNEL REMOTE INTERFACE
V(1/2)WT	-	VOICE/FAX CHANNEL WINK TIMER

Image 46

Contents MultiMux Page MultiMux #MMV1600C #MMV3200C Record of Revisions RevisionDescriptionTable of Contents Troubleshooting CommandsOperating Procedures Service, Warranty and Tech SupportTables AboutThisManual Service, Warranty and Tech Support Description of Statistical Multiplexing Background1.1 Statistical Multiplexing Communications Product DescriptionMultiMux MMV1600/3200 Series Block Diagram Page Dual Composite Links System Features Voice/FaxNetworking Dynamic Load BalanceDiagnostics Channel SwitchingCommand Modem Parameter MemoryResponse Time Control Dynamic BufferingSynchronous Data Channel AU7USA-18883-DE-N DSU FCC Regulations for Telephone Line InterconnectionDOC Terminal Equipment AU7USA-20328-MD-EComposite Link Specifications Async Data ChannelsSystem Control Internal DSUCompatibility Voice ChannelsElectrical/Physical DtmfConfiguration Description Model DescriptionConfiguration Configuration 1 Remote Site Channel Parameters Configuration 1 Local Site Channel ParametersConfiguration 1 Composite Link Configuration Configuration 2 Composite Link Configuration Remote Site Configuration 3 Remote Site 1 Channel Parameters Configuration 3 Local Site Channel ParametersConfiguration 3 Remote Site 2 Channel Parameters Configuration 4 FXO to FXS Configuration 4 Local Site Voice/Fax Channel ParametersConfiguration 4 Remote Site Voice/Fax Channel Parameters Configuration 5 E&M Configuration 5 Local site Voice/Fax Channel Parameters Configuration 5 Remote Site Voice/Fax Channel ParametersConfiguration 6 FXS to FXS Configuration 6 Local Site Voice/Fax Channel Parameters Configuration 6 Remote Site Voice/Fax Channel ParametersRemote Site Configuration 7 Local Site Voice/Fax Channel Parameters Configuration 7 Remote Site Voice/Fax Channel ParametersConfiguration 8 LAN to LAN Page StepProcedure InstallationProcedureCabling Procedure External Modem/DSU with RS232C InterfaceSync Data Channel Port B only Step ProcedureV.35 Interface Async ChannelComposite Link Cabling Configuration Procedure Supervisory ConsoleCommand Modem Step Procedure Async Channels Step Procedure Voice/Fax ChannelsPage Type Command Description Command SummaryATC1B4800P1F1E0 $DSUBCL SNGA..H $DSUACL $DSUASPGeneral Commands CommandDescription#MA Parameters H command menu is as follows General HelpStore New HelpH6 menu is as follows H4 menu is as followsH5 menu is as follows H7 menu is as followsChannel Parameter Commands ENQ/ACK DTRMLA/B/D SB1 SB2$DSUSP Composite Link Speed and Clocking Commands$DSUCL $ MuxacliAdditional Composite Link Commands $MUXBReport Retransmit TimerList Composite #RBxxxxxVoice/Fax Channel Commands Command Level Local Interface WireSilence Suppression ATV1/2LIFXOATV1/2RIFXO Test CommandsATV1/2LIFXSL ATV1/2RIFXSGT11 Command Modem CommandsT12 Configuration of Port a Composite Link MultiMuxOperatingProceduresMultiMux Operating Procedures Configuration of Port B Composite LinkConfiguration of Port B Sync Data Voice/Fax Operating Procedures Voice/Fax Operating ProceduresCommand Modem Operating Procedures Command Modem Operating ProceduresCommand Modem Access on Command modem operation and put ImportanceofCompositeStatistics IntroductionData Troubleshooting Guide TroubleshootingGuideTestCables RD LED on RD OFF Voice/Fax Troubleshooting Guide Voice/fax channelCannot communicate Channel Device Testing Procedure ChannelDeviceTestingLocal Loop Test #4 DSU and Communications Line Testing Procedure DSUandCommunicationsLineTestingRemote Digital Loop Test #5 MultiMux Functional Testing Procedures MultiMuxFunctionalTestingProceduresWatch DOG Test Passed Voice/Fax Channel Testing Procedure Voice/FaxChannelTestingVOICE/FAX Loopback Test #12 SyncDataChannelTesting Sync Data Channel Testing ProcedureService, Warranty and Tech Support Repair Procedures for International Distributors Ascii Character Code/Hex/Decimal Conversion Chart AppendixASignal Information Negative Positive Appendix BCabling Diagrams Appendix CCommand Port Cables DCE to DTE cablingComposite Link Cabling RJ48 Cabling for Internal DSU Description FXO Description FXS Description RJ45 Spade Lug Wire Color FunctionVoice/Fax Channel Connectors I-V Voice/Fax Channel CableRepeat Command Name DefaultAnswer a LastATO ATH1ATH0 ATQ1Read or ATD5551212RRegister WriteUser Profiles Configuration displaysView Active Store ActiveATX1 ATX0ATX2 Returning to Command ExecutionMode While After DialIndicator Description Table E-1. LED IndicatorsAppendix E Back Panel LED Indicators DescriptionFCR BPS Modem DIAL-UP Line Connector ON/OFF SwitchPower Connector Command Port TERMINAL/PC ConnectorVOICE/FAX Channel 1 E&M Connector VOICE/FAX Channel 2 FXS ConnectorVOICE/FAX Channel 2 FXO Connector VOICE/FAX Channel 1 FXS ConnectorRS232C/V.35 Shunt Channel Board Number of Channels SwitchChannel # Appendix F Flow Control BackgroundOff Printer pacing and Flow Control Glossary of Terms Page Format Page Parameter Page Page Symbols DOC DSUFXO FXS External Composite LinkLads MultiMux Functional Testing Procedure List Channel Parameters CommandLoad DSU Factory Defaults Command Link ProtocolREN PDNPstn RJ48STransmit XMT Indicator Stop Bit Command SB1-SB2Stdm Word Length Select Command WL5-8 Voice/Fax Channel Testing ProcedureVoice/Fax Input Level Gain Command Voice/Fax Channels