Multi-Tech Systems MMV1600 owner manual Voice/Fax Channel Commands

		E	L	E	E		E	L	E	E
		T	O	M	S		T	O	M	S
C		R	C	O	T	C	R	C	O	T
A		A	T	T		A	A	T	T
R		N	R	E		R	N	R	E
R		S	L		M	R	S	L		M
I R X C		M	R	D	O	I R X C M R			D	O
E C M T		I	C	W	D	E C M T I		C	W	D
R	V T S T		V	N	E	R V T S T		V	N	E
#	X X #					# X	X #

5.2.5

Voice/Fax Channel Commands

The Voice/Fax Channel commands control the traffic of the voice and fax communication over the composite link network. The

Voice/Fax Channel commands are described in detail below:
List The Voice/Fax	List The Voice/Fax Channel Parameters command causes the
Channel	MultiMux to display the parameters for the Voice/Fax channels
Parameters	on the system's supervisory console as shown in the following					example. The Voice/
Fax channel parameters display general			VL parameters for both channels and the local and remote channel
	interfaces. To display the parameters for the Voice/Fax channels,					you would enter ATVL
and hit your Return key.
LOCAL VOICE/FAX PARAMETERS CHANNEL1 LOCAL VOICE/FAX PARAMTERS CHANNEL 2
PARAMETER		STATUS	PARAMETER		STATUS
DESTINATION CHANNEL		01	DESTINATION CHANNEL		02
DESTINATION NODE		01	DESTINATION NODE		01
LINK A/B/D		A	LINK A/B/D		A
DIGITIZING RATE		16000	DIGITIZING RATE		16000
OUTPUT LEVEL ATTEN.		12	OUTPUT LEVEL ATTEN.		12
INPUT LEVEL GAIN		03	INPUT LEVEL GAIN		03
SILENCE SUPPRESSION		02	SILENCE SUPPRESSION		02
LOCAL INTERFACE TYPE		FXS	LOCAL INTERFACE TYPE		FXS
GROUND/LOOP START (FXS)		LOOP	GROUND/LOOP START (FXS)		LOOP
2 OR 4 WIRE (E&M)		2 WIRE	2 OR 4 WIRE (E&M)		2 WIRE
DIALTONE/WINK (E&M)		N/A	DIALTONE/WINK (E&M)		N/A
WINK TIMER		N/A	WINK TIMER		N/A
REMOTE INTERFACE TYPE		FXS	REMOTE INTERFACE TYPE		FXS
GROUND/LOOP START (FXS)		LOOP	GROUND/LOOP START (FXS)		LOOP
2 OR 4 WIRE (E&M)		2 WIRE	2 OR 4 WIRE (E&M)		2 WIRE
DIALTONE/WINK (E&M)		N/A	DIALTONE/WINK (E&M)		N/A
Reset	The Reset	Voice/Fax Channel command sets the operating
Voice/Fax	parameters for the voice/fax channel to the most recently
Channel	stored values and resets that channel.
V(1/2)Z
Voice/Fax	The Voice/Fax Destination Channel command selects which
Destination	voice/fax channel (1 or 2) on the destination MultiMux will receive
Channel	the voice/fax information. Local voice channel 1 (V1) can select
V(1/2)DC	destination channel 1 DC1 or destination channel 2 DC2 to					receive the information.
Similarily, V2 can select DC1 or DC2.
Voice/Fax	The voice/Fax Destination Node command (V(1/2)DN(0-31))
Destination Node	selects the destination MultiMux (0-31) for which voice/fax data					will be sent. The voice/
fax channels 1 or 2 can select destination			V(1/2)DN	nodes from 0 to 31. Voice/fax channel 1 can select a
destination	node of 25 using V1DN25 command.
Link the Voice/Fax	The Link the voice/Fax Channel will Communicate Over command
Channel will	(V(1/2)ML(A/B/D)) selects the composite link (A/B/D) in which
Communicate Over	the voice/fax data will be sent. Local voice/fax channel 1 can					send voice/fax data
over composite link A by executing V1MLA			V(1/2)ML	command. The V2MLD command enables voice/fax channel