Configuration of Port B Sync Data | Multi-Tech Systems MMV1600

The following will be displayed on your system monitor if your MultiMux is configured with Port B as a synchronous data channel:

Configuration of Port A: Composite Link

DSU TYPE SPEED CLOCKINGLOOPBACK

EXTERNAL 56K INTERNAL OFF

Configuration of Port B: Sync Data

DSU TYPE SPEED CLOCKINGLOOPBACK

ANY SDLC 56K INTERNAL OFF

Based on the listed composite link configuration conditions, reconfigure the parameters to the conditions required in your particular installation by entering the appropriate Internal Composite Link Configuration Commands as described in Chapter 5 of this manual. If you wish to save new parameters, you must execute a AT&W command.

6If you wish to display the remote parameter status screen for downline	loading, execute the Select Downline
Load Parameters command by entering the following:
AT&SR (hit Return)

Table 6-1. MultiMux Operating Procedures (cont.)

StepProcedure

The following will be displayed on your supervisory console:

					Down line Load Channel Parameters
			STP		FLOW	ENQ/			PASS PASS DEST DEST LINK
CHN	SPD WD BIT PAR				CTRL	ACK ECHO PACE			EIA	XON	CHN NODE A/B
01	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	01	00	A
02	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	02	00	A
03	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	03	00	A
04	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	04	00	A
05	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	05	00	A
06	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	06	00	A
07	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	07	00	A
08	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	08	00	A
09	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	09	00	A
10	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	10	00	A
11	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	11	00	A
12	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	12	00	A
13	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	13	00	A
14	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	14	00	A
15	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	15	00	A
16	19200	8	1	NONE	XON/XOFF	OFF	OFF	OFF	OFF	OFF	16	00	A

This display is not a listing of the actual parameters, but shows what can be downline loaded.

7After the remote parameter status screen is displayed, hit Return to display the Remote Source Node Number Group Select screen that permits you to update either 16 channel entries for an MMV1600 series or 32 channel entries for an MMV3200 series.

Source Node For Group A (Channels 1-4)=xxx

Source Node For Group B (Channels 5-8)=xxx

Source Node For Group C(Channels 9-12)=xxx

Source Node For Group D (Channels 13-16)=xxx

Source Node For Group E (Channels 17-20)=xxx

Source Node For Group F (Channels 21-24)=xxx

Source Node For Group G (Channels 25-28)=xxx

Source Node For Group H (Channels 29-32)=xxx

For example, if your MultiMux MMV3200 series is connected to another 32 channel MultiMux with a source node (SN) of 199, set all channels to 199 by entering ATSNGA199<CR>, then ATSNGB199, etc.