RedMax HC510DV manual Fueling the Unit, For Your Engine LIFE, Avoid

Page 15

7. Fuel

again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.

5.Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers.

6.Indicate the contents on outside of container for easy identification.

FUELING THE UNIT

1.Untwist and remove the fuel cap. Rest the cap on a dustless place.

2.Put fuel into the fuel tank to 80% of the full capacity.

3.Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING

1.Select bare ground for fueling.

2.Move at least 10feet (3meters) away from the fueling point before starting the engine.

3.Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID;

1.FUEL WITH NO OIL(RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.

2.GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.

3.OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.

4.Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly.

5.In the case of storing the product for a

long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.

6.In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site.

NOTE

As lot details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to fhe mixed gasoline, etc. described therein, if may not be covered by the warranty.

15

Image 15
Contents T2069-93110 HC510DVPage Contents Safety FirstSpecifications Parts location 4   5   6  Symbols on the machineBefore Using the Machine For safe operation 7   8  Working Gear and Clothing 9   10  Operation Safety PrecautionsMaintenance Safety Precaution After Using the SAW 11   12  Set upSE1 Change of Dust StopperDust hose Metal band Dust bag Tying Cord SE2 SE3 SE4 Mounting of Cutter BladeCutter blade Flange bolt Flange washer a Fitting Dust Hose and Dust BAGRecommended Mixing Ratio Gasoline 50OIL HOW to MIX FuelFuel  14 For Your Engine LIFE, Avoid Fueling the Unit 16  OperationOP1 OP2 Starting Engine CloseSafety lock Start setting button Throttle lever OP3 OP4 OP5Decomp valve OFF SwitchOP6 Stopping EngineVertical Cutting OP7 OP8 Cutting OperationFor AN Efficient Cutting Operation Front guide Horizontal CuttingMA1 MaintenanceAIR Cleaner Air cleaner cover Top plate Felt filterNGK BPM8Y MA2MA3 Spark PlugMA4 MA5 Cooling AIR Passage Blade Drive Belt 22  Disassembling Procedure MA6 MA7 MA8 MA9Belt Exchange  24  Assembling Procedure 25  FAN Drive Belt Belt Tension Adjustment and ExchangeIdler pulley Belt adjustment plate Bolt Tighten Slacken MA14 26  Engine Adjustment MA15When adjusting, take the following steps MA15 27   28  Starter Rope ExchangeNotch MA19 MA20 MA21 30   31  StorageTroubleshooting guide Check Probable Causes Action 32   33  Parts list 34  Cutter Unit HC510DV S/N 200101 and up 35   36  Power Unit 1 HC510DV S/N 200101 and up 37   38  Power Unit 2 HC510DV S/N 200101 and up 39   40  Carburetor HC510DV S/N 200101 and up 41  Accessories & Tool SET HC510DV S/N 200101 and upManufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée