RedMax HC510DV manual Manufacturer’s warranty coverage

Page 42

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards. KOMATSU ZENOAH must warrant the emission control system on your small off-road engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carburetor and the ignition system.

Where a warrantable condition exists, KOMATSU ZENOAH will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

Manufacturer’s warranty coverage:

The 1995 and later small off-road engines are warranted for two years. If any emission- related part on your engine is defective, the part will be repaired or replaced by

KOMATSU ZENOAH.

Owner’s warranty responsibilities:

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. KOMATSU ZENOAH recommends that you retain all receipts covering maintenance on your small off-road engine, but KOMATSU ZENOAH can not deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the small off-road engine owner, you should be aware, however, that KOMATSU ZENOAH may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modification.

You are responsible for presenting your small off-road engine to a KOMATSU ZENOAH distribution center as soon as a problem exists. The warranty repairs should be completed in e reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact KOMATSU ZENOAH AMERICA INC. at (770)-381-5147 or you can write to

KOMATSU ZENOAH AMERICA INC.

4344 Shackleford Road Suite 500

Norcross, Georgia 30093

Image 42
Contents HC510DV T2069-93110Page Safety First ContentsSpecifications Parts location 4   5  Symbols on the machine  6 Before Using the Machine For safe operation 7  Working Gear and Clothing  8  9  Operation Safety Precautions  10 Maintenance Safety Precaution After Using the SAW 11  Change of Dust Stopper Set upSE1  12 Fitting Dust Hose and Dust BAG SE2 SE3 SE4 Mounting of Cutter BladeCutter blade Flange bolt Flange washer a Dust hose Metal band Dust bag Tying Cord 14  HOW to MIX FuelFuel Recommended Mixing Ratio Gasoline 50OILFueling the Unit For Your Engine LIFE, AvoidClose OperationOP1 OP2 Starting Engine  16 Safety lock Start setting button Throttle lever OP3 OP4 OP5Decomp valve Stopping Engine SwitchOP6 OFFFront guide Horizontal Cutting OP7 OP8 Cutting OperationFor AN Efficient Cutting Operation Vertical CuttingAir cleaner cover Top plate Felt filter MaintenanceAIR Cleaner MA1Spark Plug MA2MA3 NGK BPM8YMA4 MA5 Cooling AIR Passage Blade Drive Belt 22  Disassembling Procedure MA6 MA7 MA8 MA9Belt Exchange Assembling Procedure  24 MA14 FAN Drive Belt Belt Tension Adjustment and ExchangeIdler pulley Belt adjustment plate Bolt Tighten Slacken  25 MA15 Engine Adjustment MA15When adjusting, take the following steps  26  27  Starter Rope Exchange  28 MA19 MA20 MA21 Notch 30  Storage  31 Troubleshooting guide Check Probable Causes Action 32  Parts list  33 Cutter Unit HC510DV S/N 200101 and up  34  35  Power Unit 1 HC510DV S/N 200101 and up  36  37  Power Unit 2 HC510DV S/N 200101 and up  38  39  Carburetor HC510DV S/N 200101 and up  40 Accessories & Tool SET HC510DV S/N 200101 and up  41 Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée