Graco 312359J Wire Sprayers with Explosion-Proof Heaters, Connect Air Supply

Page 21

Wire Sprayers with Explosion-Proof Heaters

(Hazardous location sprayers only)

If your sprayer is rated for hazardous areas, and you have explosion-proof heaters, you must have a quali- fied electrician connect heater wiring. Ensure wiring and installation comply with local electrical codes for hazardous areas.

Improperly installed or connected equipment will create a hazardous condition and cause fire, explosion, or elec- tric shock. Follow local regulations.

When explosion-proof heaters are used, ensure wiring, wiring connections, switches, and electrical distribution panel all meet flame-proof (explosion-proof) require- ments.

Refer to Viscon HP heater manual 309524 for electrical connection instructions and guidelines in hazardous locations.

Setup

Connect Air Supply

Connect air supply line to 3/4 npt(f) air filter inlet.

NOTE:

Use a 3/4 in. (19.1 mm) ID minimum air hose.

E

NOTE:

Air supply requirement: 150 psi (1.0 MPa, 10.3 bar) maximum; 50 psi (0.35 MPa, 3.5 bar) minimum (while running).

Flow volume required: 70 scfm (1.96 m3/min) minimum;

250scfm (7.0 m3/min) maximum. Available fluid pres- sure and flow rate are directly related to available air vol- ume. See Pump Performance Charts, page 83.

General flow volume guidelines:

70 scfm (1.96 m3/min) per gpm (lpm) while spraying

10 scfm (0.28 m3/min) added per agitator

10 scfm (0.28 m3/min) added per drum feed pump

NOTE:

If your sprayer is for use in hazardous areas, the control box is powered by an air-driven alternator.

NOTE:

Dosing valves are operated by air. The sprayer will not operate correctly if the inlet air gauge drops below 50 psi (0.35 MPa, 3.5 bar) while spraying.

312359J

21

Image 21
Contents XM Plural-Component Sprayers312359J Contents Manual Description Related ManualsFire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Location Category Key ModelsXM a XM B XM D XM C XM E ApprovalsCode FiltersUsage Material Self-Ignition OverviewIsocyanate Hazard Moisture Sensitivity IsocyanatesComponents a and B Changing MaterialsKeep Components a and B Separate Lift Using a Hoist Lift Using a ForkliftLocation Proper Lifting of SprayerInitial System Setup Component Identification Typical Setup 20 Gallon Hoppers with Recirculation Back View Fluid Control Assembly Fluid Control AssemblyAir Controls Junction Box/Heater ControlsIG Junction Box/Heater Controls IG Air ControlsLEDs User InterfaceInterface Display, Main Display Screen Components User Interface DisplaySetup Connect Power CordPower Cord Requirements Configure to Supply Power Non-hazardous location sprayers onlyTerminal Blocks Wire Sprayers with Explosion-Proof Heaters Connect Air SupplyHazardous location sprayers only Adjust Packing Nuts Connect Fluid Hose AssemblyBasic Operation Set System Settings Optional Set User Interface ParametersSet USB Parameters Set Maintenance Parameters Optional Set Maintenance ScheduleSet Maintenance Setpoints Set Temperature Limits Set Sprayer Limits OptionalSet Pressure Limits Prime Prime a and B FluidsGallon Hopper Shown Prime Prime Solvent Flush Pump Without Heat RecirculateHeat Fluid With HeatSpray Mix Manifold Restriction Stem Adjust B Machine Outlet RestrictionPressure Relief Procedure Relieve a and B Fluid PressureRelieve Pump Fluid Pressure and Flush Mix Hose To flush mixed material out of line with clean solvent Flush Mixed Material Flush Mix ManifoldUse Solvent Pump Follow Pressure Relief Procedure, Park Fluid Pump Rods Relieve pressure. See Pressure Relief Procedure,Follow Park Fluid Pump Rods on Shutdown Entire SystemSystem Verification Mix and Integration TestsPump and Metering Test System Verification Confirm Pump Test Batch Ratio Dispense Test Confirm Batch Dispense Test Down Stream Valve Leak TestXM Setup and Troubleshooting Guide Guidelines ProcedureFollow Park Fluid Pump Rods, Download Procedure Download SetupDownload Data from USB USB LogsDownload Data from USB Cleaning Procedure MaintenanceFilters SealsDiagnose Alarms AlarmsClear Alarms Icon FunctionAlarm Code Alarm Problem When Active Cause Solution Alarm Codes and TroubleshootingAdjust B Machine Outlet Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Mode Control Logic Alarms Possible Alarms by ModeAlarm Code Key LED Diagnostic InformationModule Status LED Signal Diagnosis Solution What Alert WhereAccessories and Kits Desiccant Dryer Kit Electric Heated Hose Power Supply KitCaster Kit Hose Rack KitCommand Functions key OFF or removed Setup Functions key onAppendix a User Interface DisplaySetup Mode Screens Home Setup Screens Icon FunctionHome Set Potlife/Hose Length System Setup ScreensPump Configuration System Number and USB SettingsFast Dosing Function Advisory B3A Alarm B4A Enable Setup ScreensMaintenance Setup Maintenance Setup ScreensUser Limits Setup Screens Process Pressure Limits for spray modeProcess Temperature Limits for spray mode Alarm Control Screens Operator Command Functions ScreensTest Screens Fluid Control ScreensRun Fluid Control Screens Power On/Enter ModeConfirm Pump Test Ratio ModeBatch Dispense Test Down Stream Valve Leak TestConfirm Batch Dispense Test Alarm Maintenance 2 Screen Maintenance 1 ScreenReset Maintenance Counter Totalizers and Job NumberPotlife Screen Auto Display ScreensUSB Screen Recommended USB Flash DrivesExample Spray Log Metering Diagrams Metering Diagram without Remote Mix ManifoldAppendix B Metering Diagram with Remote Mix Manifold XM Metering Diagram with Remote Mix ManifoldPower Cord Guidelines Power Cord GuidelinesAppendix C System Dimensions without Hoppers DimensionsSystem Dimensions with Hoppers Two 20-Gallon Hoppers Side MountedTwo 20-Gallon Hoppers Rear Mounted Two 7-Gallon Hoppers One 20-Gallon Hopper and One 7-Gallon HopperCalculate Fluid Outlet Pressure Pump Performance ChartsCalculate Pump Air Consumption XM50 Fluid Performance and Air ConsumptionPerformance Charts , Technical DataTechnical Data 312359J Graco Information Graco Standard Warranty

312359J specifications

The Graco 312359J is a versatile paint sprayer designed for both DIY enthusiasts and professionals alike. Known for its powerful performance and user-friendly features, this sprayer is ideal for various painting tasks, from small interior projects to larger exterior applications.

One of the standout features of the Graco 312359J is its robust piston pump system, which can handle thicker materials without compromising on quality. This allows users to spray a wide range of coatings, including stains, sealers, and even heavy-duty paints. The sprayer is engineered to deliver consistent pressure, ensuring an even and professional finish on every job.

Another significant characteristic of the Graco 312359J is its ability to produce a fine mist, which helps to reduce overspray and material waste. This is particularly beneficial for intricate projects where precision is critical. Additionally, the adjustable spray pattern can be easily configured to suit various tasks, allowing users to switch from broad coverage to detailed work with minimal effort.

The convenience of portability is another important aspect of the Graco 312359J. It features a lightweight design, making it easy to maneuver around different work areas. The integrated carrying handle further enhances mobility, allowing users to transport the sprayer without hassle.

In terms of technology, the Graco 312359J incorporates an easy-to-use control system, ensuring that even beginners can achieve professional-quality results. The user-friendly design simplifies setup and maintenance, while the quick-connect nozzle system allows for easy changes between different spray tips.

Moreover, the sprayer is equipped with a durable and easy-to-clean design. Users can quickly flush out the system after use, saving time and maintaining the equipment's longevity.

Ultimately, the Graco 312359J stands out for its combination of power, portability, and advanced features, making it an excellent choice for anyone looking to achieve a flawless finish. Its blend of practicality and efficiency caters to a wide range of applications, helping both novice and experienced users achieve outstanding results with ease. Whether tackling a home renovation or a professional job, this paint sprayer is designed to meet various painting needs effectively.