Graco 312359J important safety instructions Prime a and B Fluids, Gallon Hopper Shown

Page 27

Prime

Prime A and B Fluids

Wear gloves when using flush solvents and/or if fluid temperature exceeds 110° F (43° C).

NOTE:

Do not install gun spray tip yet. To avoid splashing, use the lowest pressure possible to prime.

1.Condition materials prior to adding to hoppers. Ensure resin materials are thoroughly agitated, homogenous, and pourable prior to adding to hop- per. Stir hardeners back into suspension prior to adding material to hopper.

2.Fill A and B reservoirs with proper materials. Fill A side with major volume of material; fill B side with minor volume of material.

20 Gallon Hopper Shown

3. Move recirculation lines to empty containers.

7. Use manual pump run mode.

Prime

4. Open ball valves into pumps.

5.Turn mix manifold valves (AH, AJ) clockwise to close them.

AJ

AH

6.Turn on air supply. Set main pump air regulator (CD) to 20 psi (138 kPa 1.38 bar).

CD

312359J

27

Image 27
Contents XM Plural-Component Sprayers312359J Contents Manual Description Related ManualsFire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Location Category Key ModelsFilters ApprovalsXM a XM B XM D XM C XM E CodeMoisture Sensitivity Isocyanates OverviewUsage Material Self-Ignition Isocyanate HazardComponents a and B Changing MaterialsKeep Components a and B Separate Proper Lifting of Sprayer Lift Using a ForkliftLift Using a Hoist LocationInitial System Setup Component Identification Typical Setup 20 Gallon Hoppers with Recirculation Back View Fluid Control Assembly Fluid Control AssemblyIG Air Controls Junction Box/Heater ControlsAir Controls IG Junction Box/Heater ControlsLEDs User InterfaceInterface Display, Main Display Screen Components User Interface DisplaySetup Connect Power CordPower Cord Requirements Configure to Supply Power Non-hazardous location sprayers onlyTerminal Blocks Wire Sprayers with Explosion-Proof Heaters Connect Air SupplyHazardous location sprayers only Adjust Packing Nuts Connect Fluid Hose AssemblyBasic Operation Set System Settings Optional Set User Interface ParametersSet USB Parameters Set Maintenance Parameters Optional Set Maintenance ScheduleSet Maintenance Setpoints Set Temperature Limits Set Sprayer Limits OptionalSet Pressure Limits Prime Prime a and B FluidsGallon Hopper Shown Prime Prime Solvent Flush Pump Without Heat RecirculateHeat Fluid With HeatSpray Mix Manifold Restriction Stem Adjust B Machine Outlet RestrictionPressure Relief Procedure Relieve a and B Fluid PressureRelieve Pump Fluid Pressure and Flush Mix Hose To flush mixed material out of line with clean solvent Flush Mixed Material Flush Mix ManifoldUse Solvent Pump Follow Pressure Relief Procedure, Park Fluid Pump Rods Relieve pressure. See Pressure Relief Procedure,Follow Park Fluid Pump Rods on Shutdown Entire SystemSystem Verification Mix and Integration TestsPump and Metering Test System Verification Confirm Pump Test Batch Ratio Dispense Test Confirm Batch Dispense Test Down Stream Valve Leak TestXM Setup and Troubleshooting Guide Guidelines ProcedureFollow Park Fluid Pump Rods, USB Logs Download SetupDownload Procedure Download Data from USBDownload Data from USB Seals MaintenanceCleaning Procedure FiltersIcon Function AlarmsDiagnose Alarms Clear AlarmsAlarm Code Alarm Problem When Active Cause Solution Alarm Codes and TroubleshootingAdjust B Machine Outlet Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Mode Control Logic Alarms Possible Alarms by ModeWhat Alert Where LED Diagnostic InformationAlarm Code Key Module Status LED Signal Diagnosis SolutionAccessories and Kits Hose Rack Kit Electric Heated Hose Power Supply KitDesiccant Dryer Kit Caster KitUser Interface Display Setup Functions key onCommand Functions key OFF or removed Appendix aSetup Mode Screens Home Setup Screens Icon FunctionHome Set Potlife/Hose Length System Setup ScreensPump Configuration System Number and USB SettingsFast Dosing Function Advisory B3A Alarm B4A Enable Setup ScreensMaintenance Setup Maintenance Setup ScreensUser Limits Setup Screens Process Pressure Limits for spray modeProcess Temperature Limits for spray mode Fluid Control Screens Operator Command Functions ScreensAlarm Control Screens Test ScreensRun Fluid Control Screens Power On/Enter ModeConfirm Pump Test Ratio ModeBatch Dispense Test Down Stream Valve Leak TestConfirm Batch Dispense Test Alarm Totalizers and Job Number Maintenance 1 ScreenMaintenance 2 Screen Reset Maintenance CounterRecommended USB Flash Drives Auto Display ScreensPotlife Screen USB ScreenExample Spray Log Metering Diagrams Metering Diagram without Remote Mix ManifoldAppendix B Metering Diagram with Remote Mix Manifold XM Metering Diagram with Remote Mix ManifoldPower Cord Guidelines Power Cord GuidelinesAppendix C System Dimensions without Hoppers DimensionsSystem Dimensions with Hoppers Two 20-Gallon Hoppers Side MountedTwo 20-Gallon Hoppers Rear Mounted Two 7-Gallon Hoppers One 20-Gallon Hopper and One 7-Gallon HopperXM50 Fluid Performance and Air Consumption Pump Performance ChartsCalculate Fluid Outlet Pressure Calculate Pump Air ConsumptionPerformance Charts , Technical DataTechnical Data 312359J Graco Information Graco Standard Warranty

312359J specifications

The Graco 312359J is a versatile paint sprayer designed for both DIY enthusiasts and professionals alike. Known for its powerful performance and user-friendly features, this sprayer is ideal for various painting tasks, from small interior projects to larger exterior applications.

One of the standout features of the Graco 312359J is its robust piston pump system, which can handle thicker materials without compromising on quality. This allows users to spray a wide range of coatings, including stains, sealers, and even heavy-duty paints. The sprayer is engineered to deliver consistent pressure, ensuring an even and professional finish on every job.

Another significant characteristic of the Graco 312359J is its ability to produce a fine mist, which helps to reduce overspray and material waste. This is particularly beneficial for intricate projects where precision is critical. Additionally, the adjustable spray pattern can be easily configured to suit various tasks, allowing users to switch from broad coverage to detailed work with minimal effort.

The convenience of portability is another important aspect of the Graco 312359J. It features a lightweight design, making it easy to maneuver around different work areas. The integrated carrying handle further enhances mobility, allowing users to transport the sprayer without hassle.

In terms of technology, the Graco 312359J incorporates an easy-to-use control system, ensuring that even beginners can achieve professional-quality results. The user-friendly design simplifies setup and maintenance, while the quick-connect nozzle system allows for easy changes between different spray tips.

Moreover, the sprayer is equipped with a durable and easy-to-clean design. Users can quickly flush out the system after use, saving time and maintaining the equipment's longevity.

Ultimately, the Graco 312359J stands out for its combination of power, portability, and advanced features, making it an excellent choice for anyone looking to achieve a flawless finish. Its blend of practicality and efficiency caters to a wide range of applications, helping both novice and experienced users achieve outstanding results with ease. Whether tackling a home renovation or a professional job, this paint sprayer is designed to meet various painting needs effectively.