Graco 312359J Flush Mixed Material, Flush Mix Manifold, Use Solvent Pump

Page 36

Flush Mixed Material

Flush Mixed Material

Flush Mix Manifold

Use Solvent Pump

1.Press to turn off system. Engage trigger lock. Remove spray tip.

 

4)!

TI1949a

TI1948a

2.Ensure sampling valves (AE, AF) and mix manifold valves (AH, AJ) are closed.

4.Open solvent pump air valve (CB). Pull out and slowly turn solvent pump air regulator (CG) clock- wise to increase air pressure. Use lowest possible pressure.

.

CG

CB

5.Disengage trigger lock and trigger gun into a grounded pail. Use a pail lid with a hole to dispense through. Seal around hole and gun with a rag to pre- vent splash back. Be careful to keep fingers away from front of gun. Flush out mixed material until clean solvent dispenses.

AE

AH

AF

AK

AJ

TI1950a

TI1953a

 

6. Engage trigger lock.

TI1949a

3. Open solvent shutoff valve (AK) at mix manifold.

36

312359J

Page 35 Page 37
Image 36
Page 35 Page 37
Contents XM Plural-Component Sprayers312359J Contents Related Manuals Manual DescriptionFire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Models Location Category KeyApprovals XM a XM B XM D XM C XM ECode FiltersOverview Usage Material Self-IgnitionIsocyanate Hazard Moisture Sensitivity IsocyanatesComponents a and B Changing MaterialsKeep Components a and B Separate Lift Using a Forklift Lift Using a HoistLocation Proper Lifting of SprayerInitial System Setup Component Identification Typical Setup 20 Gallon Hoppers with Recirculation Back View Fluid Control Assembly Fluid Control AssemblyJunction Box/Heater Controls Air ControlsIG Junction Box/Heater Controls IG Air ControlsUser Interface LEDsUser Interface Display Interface Display, Main Display Screen ComponentsSetup Connect Power CordPower Cord Requirements Configure to Supply Power Non-hazardous location sprayers onlyTerminal Blocks Wire Sprayers with Explosion-Proof Heaters Connect Air SupplyHazardous location sprayers only Connect Fluid Hose Assembly Adjust Packing NutsBasic Operation Set System Settings Optional Set User Interface ParametersSet USB Parameters Set Maintenance Parameters Optional Set Maintenance ScheduleSet Maintenance Setpoints Set Temperature Limits Set Sprayer Limits OptionalSet Pressure Limits Prime Prime a and B FluidsGallon Hopper Shown Prime Prime Solvent Flush Pump Recirculate Without HeatWith Heat Heat FluidSpray Adjust B Machine Outlet Restriction Mix Manifold Restriction StemPressure Relief Procedure Relieve a and B Fluid PressureRelieve Pump Fluid Pressure and Flush Mix Hose To flush mixed material out of line with clean solvent Flush Mixed Material Flush Mix ManifoldUse Solvent Pump Follow Pressure Relief Procedure, Relieve pressure. See Pressure Relief Procedure, Park Fluid Pump RodsShutdown Entire System Follow Park Fluid Pump Rods onSystem Verification Mix and Integration TestsPump and Metering Test System Verification Confirm Pump Test Batch Ratio Dispense Test Down Stream Valve Leak Test Confirm Batch Dispense TestXM Setup and Troubleshooting Guide Procedure GuidelinesFollow Park Fluid Pump Rods, Download Setup Download ProcedureDownload Data from USB USB LogsDownload Data from USB Maintenance Cleaning ProcedureFilters SealsAlarms Diagnose AlarmsClear Alarms Icon FunctionAlarm Codes and Troubleshooting Alarm Code Alarm Problem When Active Cause SolutionAdjust B Machine Outlet Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Possible Alarms by Mode Mode Control Logic AlarmsLED Diagnostic Information Alarm Code KeyModule Status LED Signal Diagnosis Solution What Alert WhereAccessories and Kits Electric Heated Hose Power Supply Kit Desiccant Dryer KitCaster Kit Hose Rack KitSetup Functions key on Command Functions key OFF or removedAppendix a User Interface DisplaySetup Mode Screens Home Setup Screens Icon FunctionHome System Setup Screens Set Potlife/Hose LengthSystem Number and USB Settings Pump ConfigurationEnable Setup Screens Fast Dosing Function Advisory B3A Alarm B4AMaintenance Setup Screens Maintenance SetupUser Limits Setup Screens Process Pressure Limits for spray modeProcess Temperature Limits for spray mode Operator Command Functions Screens Alarm Control ScreensTest Screens Fluid Control ScreensPower On/Enter Mode Run Fluid Control ScreensRatio Mode Confirm Pump TestBatch Dispense Test Down Stream Valve Leak TestConfirm Batch Dispense Test Alarm Maintenance 1 Screen Maintenance 2 ScreenReset Maintenance Counter Totalizers and Job NumberAuto Display Screens Potlife ScreenUSB Screen Recommended USB Flash DrivesExample Spray Log Metering Diagrams Metering Diagram without Remote Mix ManifoldAppendix B XM Metering Diagram with Remote Mix Manifold Metering Diagram with Remote Mix ManifoldPower Cord Guidelines Power Cord GuidelinesAppendix C Dimensions System Dimensions without HoppersSystem Dimensions with Hoppers Two 20-Gallon Hoppers Side MountedTwo 20-Gallon Hoppers Rear Mounted One 20-Gallon Hopper and One 7-Gallon Hopper Two 7-Gallon HoppersPump Performance Charts Calculate Fluid Outlet PressureCalculate Pump Air Consumption XM50 Fluid Performance and Air ConsumptionTechnical Data Performance Charts ,Technical Data 312359J Graco Standard Warranty Graco Information

312359J specifications

The Graco 312359J is a versatile paint sprayer designed for both DIY enthusiasts and professionals alike. Known for its powerful performance and user-friendly features, this sprayer is ideal for various painting tasks, from small interior projects to larger exterior applications.

One of the standout features of the Graco 312359J is its robust piston pump system, which can handle thicker materials without compromising on quality. This allows users to spray a wide range of coatings, including stains, sealers, and even heavy-duty paints. The sprayer is engineered to deliver consistent pressure, ensuring an even and professional finish on every job.

Another significant characteristic of the Graco 312359J is its ability to produce a fine mist, which helps to reduce overspray and material waste. This is particularly beneficial for intricate projects where precision is critical. Additionally, the adjustable spray pattern can be easily configured to suit various tasks, allowing users to switch from broad coverage to detailed work with minimal effort.

The convenience of portability is another important aspect of the Graco 312359J. It features a lightweight design, making it easy to maneuver around different work areas. The integrated carrying handle further enhances mobility, allowing users to transport the sprayer without hassle.

In terms of technology, the Graco 312359J incorporates an easy-to-use control system, ensuring that even beginners can achieve professional-quality results. The user-friendly design simplifies setup and maintenance, while the quick-connect nozzle system allows for easy changes between different spray tips.

Moreover, the sprayer is equipped with a durable and easy-to-clean design. Users can quickly flush out the system after use, saving time and maintaining the equipment's longevity.

Ultimately, the Graco 312359J stands out for its combination of power, portability, and advanced features, making it an excellent choice for anyone looking to achieve a flawless finish. Its blend of practicality and efficiency caters to a wide range of applications, helping both novice and experienced users achieve outstanding results with ease. Whether tackling a home renovation or a professional job, this paint sprayer is designed to meet various painting needs effectively.
Top Page Image Contents