Graco 312359J important safety instructions Diagnose Alarms, Clear Alarms, Icon Function

Page 51

Alarms

View Alarms

When an alarm occurs the alarm information screen automatically displays. It shows the current alarm code along with a bell icon. It also shows the alarm location with top and side views of the sprayer.

There are two levels of alarms: warnings and advisories. A bell icon indicates an alarm. A solid bell icon with an exclamation point and three audible alerts indicate a warning. And an outlined hollow bell icon and a single audible alert indicate an advisory.

Advisories are notifications that require attention but not immediately. Alarms require immediate correction; therefore, sprayer operation automatically stops.

This screen also shows diagnostic information. There are three lines of data on the left side. The top line shows the power supply or alternator power supply. This should be between 23-25 Volts for power supply sys- tems and 10-14 Volts for alternator systems. The middle line shows the sensor voltage. This should be between 4.9-5.1 Volts.

The center of the screen shows linear sensor vertical bar graphs and reed switch information. The A side information is on the left and the B side information is on the right. Linear sensor position is displayed on the bar graph that goes up and down when the pump moves. This bar graph should move from top to bottom to match each pump stroke.

The state of the two reed switches in each air motor are shown with the arrow above each vertical bar graph.

Alarms

Icon Function

Moving up

Moving down

Top changeover

Bottom changeover

One reed switch signal is missing

Blank: No reed switch signal

Diagnose Alarms

See Alarm Codes and Troubleshooting for causes and solutions to each alarm code.

Clear Alarms

Press to clear alarms and advisories. From the

alarm information screen, press

to return to the

run (fluid control) screen.

 

312359J

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents XM Plural-Component Sprayers312359J Contents Manual Description Related ManualsFire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Location Category Key ModelsFilters ApprovalsXM a XM B XM D XM C XM E CodeMoisture Sensitivity Isocyanates OverviewUsage Material Self-Ignition Isocyanate HazardComponents a and B Changing MaterialsKeep Components a and B Separate Proper Lifting of Sprayer Lift Using a ForkliftLift Using a Hoist LocationInitial System Setup Component Identification Typical Setup 20 Gallon Hoppers with Recirculation Back View Fluid Control Assembly Fluid Control AssemblyIG Air Controls Junction Box/Heater ControlsAir Controls IG Junction Box/Heater ControlsLEDs User InterfaceInterface Display, Main Display Screen Components User Interface DisplaySetup Connect Power CordPower Cord Requirements Configure to Supply Power Non-hazardous location sprayers onlyTerminal Blocks Wire Sprayers with Explosion-Proof Heaters Connect Air SupplyHazardous location sprayers only Adjust Packing Nuts Connect Fluid Hose AssemblyBasic Operation Set System Settings Optional Set User Interface ParametersSet USB Parameters Set Maintenance Parameters Optional Set Maintenance ScheduleSet Maintenance Setpoints Set Temperature Limits Set Sprayer Limits OptionalSet Pressure Limits Prime Prime a and B FluidsGallon Hopper Shown Prime Prime Solvent Flush Pump Without Heat RecirculateHeat Fluid With HeatSpray Mix Manifold Restriction Stem Adjust B Machine Outlet RestrictionPressure Relief Procedure Relieve a and B Fluid PressureRelieve Pump Fluid Pressure and Flush Mix Hose To flush mixed material out of line with clean solvent Flush Mixed Material Flush Mix ManifoldUse Solvent Pump Follow Pressure Relief Procedure, Park Fluid Pump Rods Relieve pressure. See Pressure Relief Procedure,Follow Park Fluid Pump Rods on Shutdown Entire SystemSystem Verification Mix and Integration TestsPump and Metering Test System Verification Confirm Pump Test Batch Ratio Dispense Test Confirm Batch Dispense Test Down Stream Valve Leak TestXM Setup and Troubleshooting Guide Guidelines ProcedureFollow Park Fluid Pump Rods, USB Logs Download SetupDownload Procedure Download Data from USBDownload Data from USB Seals MaintenanceCleaning Procedure FiltersIcon Function AlarmsDiagnose Alarms Clear AlarmsAlarm Code Alarm Problem When Active Cause Solution Alarm Codes and TroubleshootingAdjust B Machine Outlet Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Mode Control Logic Alarms Possible Alarms by ModeWhat Alert Where LED Diagnostic InformationAlarm Code Key Module Status LED Signal Diagnosis SolutionAccessories and Kits Hose Rack Kit Electric Heated Hose Power Supply KitDesiccant Dryer Kit Caster KitUser Interface Display Setup Functions key onCommand Functions key OFF or removed Appendix aSetup Mode Screens Home Setup Screens Icon FunctionHome Set Potlife/Hose Length System Setup ScreensPump Configuration System Number and USB SettingsFast Dosing Function Advisory B3A Alarm B4A Enable Setup ScreensMaintenance Setup Maintenance Setup ScreensUser Limits Setup Screens Process Pressure Limits for spray modeProcess Temperature Limits for spray mode Fluid Control Screens Operator Command Functions ScreensAlarm Control Screens Test ScreensRun Fluid Control Screens Power On/Enter ModeConfirm Pump Test Ratio ModeBatch Dispense Test Down Stream Valve Leak TestConfirm Batch Dispense Test Alarm Totalizers and Job Number Maintenance 1 ScreenMaintenance 2 Screen Reset Maintenance CounterRecommended USB Flash Drives Auto Display ScreensPotlife Screen USB ScreenExample Spray Log Metering Diagrams Metering Diagram without Remote Mix ManifoldAppendix B Metering Diagram with Remote Mix Manifold XM Metering Diagram with Remote Mix ManifoldPower Cord Guidelines Power Cord GuidelinesAppendix C System Dimensions without Hoppers DimensionsSystem Dimensions with Hoppers Two 20-Gallon Hoppers Side MountedTwo 20-Gallon Hoppers Rear Mounted Two 7-Gallon Hoppers One 20-Gallon Hopper and One 7-Gallon HopperXM50 Fluid Performance and Air Consumption Pump Performance ChartsCalculate Fluid Outlet Pressure Calculate Pump Air ConsumptionPerformance Charts , Technical DataTechnical Data 312359J Graco Information Graco Standard Warranty

312359J specifications

The Graco 312359J is a versatile paint sprayer designed for both DIY enthusiasts and professionals alike. Known for its powerful performance and user-friendly features, this sprayer is ideal for various painting tasks, from small interior projects to larger exterior applications.

One of the standout features of the Graco 312359J is its robust piston pump system, which can handle thicker materials without compromising on quality. This allows users to spray a wide range of coatings, including stains, sealers, and even heavy-duty paints. The sprayer is engineered to deliver consistent pressure, ensuring an even and professional finish on every job.

Another significant characteristic of the Graco 312359J is its ability to produce a fine mist, which helps to reduce overspray and material waste. This is particularly beneficial for intricate projects where precision is critical. Additionally, the adjustable spray pattern can be easily configured to suit various tasks, allowing users to switch from broad coverage to detailed work with minimal effort.

The convenience of portability is another important aspect of the Graco 312359J. It features a lightweight design, making it easy to maneuver around different work areas. The integrated carrying handle further enhances mobility, allowing users to transport the sprayer without hassle.

In terms of technology, the Graco 312359J incorporates an easy-to-use control system, ensuring that even beginners can achieve professional-quality results. The user-friendly design simplifies setup and maintenance, while the quick-connect nozzle system allows for easy changes between different spray tips.

Moreover, the sprayer is equipped with a durable and easy-to-clean design. Users can quickly flush out the system after use, saving time and maintaining the equipment's longevity.

Ultimately, the Graco 312359J stands out for its combination of power, portability, and advanced features, making it an excellent choice for anyone looking to achieve a flawless finish. Its blend of practicality and efficiency caters to a wide range of applications, helping both novice and experienced users achieve outstanding results with ease. Whether tackling a home renovation or a professional job, this paint sprayer is designed to meet various painting needs effectively.
Top Page Image Contents