Graco 332458B Intrinsic Safety, Skin Injection Hazard, Moving Parts Hazard, Toxic Fluid or Fumes

Page 6

Warnings

WARNING

INTRINSIC SAFETY

Intrinsically safe equipment that is installed improperly or connected to non-intrinsically safe equipment will create a hazardous condition and can cause fire, explosion, or electric shock. Follow local regulations and the following safety requirements.

•Be sure your installation complies with national, state, and local codes for the installation of electrical apparatus in a Class I, Group D, Division 1 (North America) or Class I, Zones 1 and 2 (Europe) Hazardous Location, including all of the local safety fire codes (for example, NFPA 33, NEC 500 and 516, OSHA 1910.107, etc.).

•To help prevent fire and explosion:

•Do not install equipment approved only for a non-hazardous location in a hazardous location. See model ID label for the intrinsic safety rating of your model.

•Do not substitute system components as this may impair intrinsic safety.

•Equipment that comes in contact with the intrinsically safe terminals must be rated for Intrinsic Safety. This includes DC voltage meters, ohmmeters, cables, and connections. Remove the unit from the hazardous area when troubleshooting.

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not point dispensing device at anyone or at any part of the body.

• Do not put your hand over the fluid outlet.

•Do not stop or deflect leaks with your hand, body, glove, or rag.

•Follow the Pressure Relief Procedure when you stop dispensing and before cleaning,

checking, or servicing equipment.

•Tighten all fluid connections before operating the equipment.

•Check hoses and couplings daily. Replace worn or damaged parts immediately.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

•Do not operate equipment with protective guards or covers removed.

•Pressurized equipment can start without warning. Before checking, moving, or servicing

equipment, follow the Pressure Relief Procedure and disconnect all power sources.

TOXIC FLUID OR FUMES

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

•Read MSDSs to know the specific hazards of the fluids you are using.

•Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

• Always wear chemically impermeable gloves when spraying, dispensing, or cleaning equipment.

6

332458B

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Important Safety Instructions ProMix PD2K Proportioner for Automatic Spray ApplicationsContents Related ManualsModels 0359Model AC2000 High Pressure Identification Label Fire and Explosion Hazard Electric Shock HazardMoving Parts Hazard Intrinsic SafetySkin Injection Hazard Toxic Fluid or FumesPersonal Protective Equipment Equipment Misuse HazardMoisture Sensitivity of Isocyanates Important Isocyanate ISO InformationIsocyanate Conditions Changing MaterialsSystem Control Drawing 16P577 Length ft mNON-HAZARDOUS Location only Hazardous Classified LocationConfigure Your System Select a Base ModelComponent Description Typical Installation Hazardous Classified Location NON-HAZARDOUS Location onlyRecommended Hose Sizes internal diameter for a and B Select HosesHose Selection Tool Viscosity Ratio Resin a Catalyst BSelect a Spray Gun Spray GunsApplication Gun Model Gun Manual No Select Non- is Color and Catalyst Change Kits Low Pressure Circulating KitsKit Part No Kit Description Select is Remote Color Change Kits Color + Solvent ValvesSelect Pump Expansion Kits General Information Mounting the PD2K Base UnitInstall the Display Module Advanced Display Module Connection PortsAir Connections Air SupplyAir Requirements Key Connection DescriptionFluid Supply Fluid RequirementsSingle Color Connections Color Change ConnectionsTSL Cup Kit Catalyst 35 cc pumps Repeat for the lower throat cartridgeSolvent Meter Accessory Light Tower AccessoryElectrical Requirements Wire KeyElectrical Supply Electrical ConnectionsGrounding Hazardous Location NON-HAZARDOUS Location KeyObject Being Sprayed Solvent Reservoir or Purge StationCheck Resistance Electrical Schematics Power ModuleEfcm Efcm J8 J9 J15 J16 J14 J10 J15 J16 Electrical Schematic, Sheet 3, Hazardous Location Optional Cables Modules Dimensions Technical Data Positive Displacement Metric ProportionerGraco Standard Warranty Graco Information
Top Page Image Contents