Carrier 48VT(N) Remove and Store in Job Files, I. Preliminary Information Model No, Temperatures

Page 37

(Remove and Store in Job Files)

START-UP CHECKLIST

(Remove and Store in Job Files)

I. PRELIMINARY INFORMATION MODEL NO.:

SERIAL NO.:

DATE:

TECHNICIAN:

II. PRESTART-UP (Insert check mark in box as each item is completed)

( ) VERIFY THAT ALL PACKING MATERIALS HAVE BEEN REMOVED FROM UNIT

( ) REMOVE ALL SHIPPING HOLD DOWN BOLTS AND BRACKETS PER INSTALLATION INSTRUCTIONS

( ) CHECK ALL ELECTRICAL CONNECTIONS AND TERMINALS FOR TIGHTNESS

( ) CHECK GAS PIPING FOR LEAKS (WHERE APPLICABLE)

( ) CHECK THAT INDOOR (EVAPORATOR) AIR FILTER IS CLEAN AND IN PLACE

( ) VERIFY THAT UNIT INSTALLATION IS LEVEL

( ) CHECK FAN WHEEL, AND PROPELLER FOR LOCATION IN HOUSING/ORIFICE AND SETSCREW TIGHTNESS

III.START-UP ELECTRICAL SUPPLY VOLTAGE COMPRESSOR AMPS

INDOOR (EVAPORATOR) FAN AMPS

TEMPERATURES

OUTDOOR (CONDENSER) AIR TEMPERATURE

DB

RETURN-AIR TEMPERATURE

DB

WB

COOLING SUPPLY AIR

DB

WB

HEAT PUMP SUPPLY AIR__________________

GAS HEAT SUPPLY AIR

PRESSURES

GAS INLET PRESSURE

IN. W.C.

GAS MANIFOLD PRESSURE

IN. W.C.

REFRIGERANT SUCTION

PSIG, SUCTION LINE TEMP*

REFRIGERANT DISCHARGE

PSIG, LIQUID TEMP{

( ) VERIFY REFRIGERANT CHARGE USING CHARGING CHARTS GAS HEAT TEMPERATURE RISE

TEMPERATURE RISE (See Literature) RANGE MEASURED TEMPERATURE RISE

* Measured at suction inlet to compressor

{Measured at liquid line leaving condenser.

48VT-- A

37

Image 37

Contents SAFETY CONSIDERATIONS TABLE OF CONTENTSFig. 1 - Unit 48VT-A Installation InstructionsINTRODUCTION RECEIVING AND INSTALLATIONStep 1 - Check Equipment Step 2 - Provide Unit Support48VT--A Fig. 2 - 48VT-A24-30Unit DimensionsA09146 48VT--A Fig. 3 - 48VT-A36-60Unit DimensionsA09147 48VT Fig. 4 - Roof Curb DimensionsSMALL CURB ROOF CURB DETAILStep 5 - Rig and Place Unit ACCESS PANELS MUST BE IN PLACE WHEN RIGGINGInspection Rigging/Lifting of Unit See FigStep 8 - Install Gas Piping Step 7 - Install Flue HoodStep 6 - Connect Condensate Drain Fig. 6 - Condensate TrapConfiguring Units for Downflow Vertical Discharge Step 9 - Install Duct ConnectionsFig. 7 - Sediment Trap FIRE OR EXPLOSION HAZARDFig. 8 - Supply and Return Duct Opening Table 1 - Physical Data - Unit 48VT-A48VT--A Horizontal Duct CoversTable 2 - Maximum Gas Flow Capacity Table 1 - Physical Data - Unit 48VT-ACont’dTable 3 - Heating Inputs 48VT--ASpecial Procedures for 208-VOperation Step 10 - Install Electrical ConnectionsHigh-VoltageConnections Control Voltage ConnectionsPRE-START-UP Balance Point Setting-Thermidistator HybridTransformer Protection ThermostatSTART-UP Step 3 - Start-upHeating and Make Adjust- mentsStep 1 - Check for Refrigerant Leaks Step 2 - Unit Sequence of OperationFig. 11 - Burner Assembly Adjust Gas InputCheck Heating Control Check Gas InputCheck Burner Flame Limit SwitchesNormal Operation Airflow and Temperature RiseRollout Switch Step 4 - Start-upCooling and Make Adjust- mentsChecking and Adjusting Refrigerant Charge Indoor Airflow and Airflow AdjustmentsContinuous Fan Operation Gas Heating Fan Speed Set-upTable 6 - Color Coding for Indoor Fan Motor Leads 48VT--ATable 8 - 48VT-AWet Coil Pressure Drop Fig. 14 - Interface Fan Board IFB48VT--A Table 7 - Filter Pressure Drop Table IN. W.CUNIT 48VT--AHeating 48VT--A1295 48VT--A1445 48VT--A1448 48VT--A48VT A Fig. 15 - 208/230-1-60Wiring Diagram, Unit 48VT-A48VT--A Fig. 16 - 208/230-3-60Wiring Diagram, Unit 48VT-AA09209 48VT--A Fig. 17 - Cooling Charging Table-Subcooling50VT500173 REV A09099Cleaning the Blower Motor and Wheel MAINTENANCEAir Filter Indoor Blower and MotorInduced Draft combustion air Blower Assembly Limit SwitchFig. 18 - Blower Housing and Flue Collector Box Fig. 19 - Unit Access PanelsOutdoor Fan Electrical Controls and WiringRefrigerant Circuit Fig. 20 - Removal of Motor and Blower WheelLoss of Charge Switch Pressure SwitchesHigh-PressureSwitch Gas InputPage LCS - Loss of Charge Switch HPS - High Pressure SwitchFig. 24 - Refrigerant Circuit AccuraterMetering De viceSTART-UPCHECKLIST TROUBLESHOOTINGUNIT OPERATION AND SAFETY HAZARD Synthetic Roof Precautionary Procedure48VT--A PURONR R-410AQUICK REFERENCE GUIDE48VT--A SYMPTOMTable 13 - Troubleshooting Guide-LEDStatus Codes Table 12 - Troubleshooting Guide-Heating48VT--A I. PRELIMINARY INFORMATION MODEL NO Remove and Store in Job FilesTEMPERATURES PRESSURESCatalog No 48VT---05SI 48VT--AEdition Date 04/09 Replaces 48VT---04SI