Grizzly G9969 Headstock Adjustment, Headstock Height & Column Rotation, Headstock Tilt

Page 28

Headstock

Adjustment

The headstock can be rotated 360º around the column, can swivel 360º in place, and can tilt 45º to the left or the right. Figure 24 shows the head- stock adjustment components.

Lock Handles

Large

Hex Bolt

Crank

Handle

Locking

Pin and

Jam Nut

Small Hex

Bolt and

Jam Nut

Figure 24. Headstock adjustment components.

Headstock Height & Column Rotation

To tilt the headstock:

1.Slightly loosen the two hex nuts at the rear of the headstock bracket.

2.Adjust the height by turning the crank han- dle.

-26-

3.Adjust the headstock rotation around the col- umn by moving the headstock to the desired position.

4.Tighten the hex nuts.

Headstock Tilt

We recommend that an assistant helps with the headstock tilt process, as the headstock is very heavy.

To tilt the headstock:

1.Loosen the large hex bolt.

2.While an assistant holds the headstock steady, turn the locking pin jam nut clockwise to draw the locking pin out. When the pin has been drawn out far enough, the head should be able to tilt.

3.Tilt the head to the desired angle and tighten the large hex bolt.

4.When returning the headstock to the 0º posi- tion, tap the locking pin back into place and tighten the hex nut against the bracket.

5.The small hex bolt and jam nut shown in Figure 24 are used to control the amount of resistance when tilting. To increase resistance, turn the hex bolt clockwise. To decrease resistance, turn the hex bolt coun- terclockwise. When resistance adjustments are complete, tighten the jam nut against the bracket.

Headstock Swivel

To swivel the headstock:

1.Loosen the two lock handles at the front of the headstock bracket.

2.Swivel the headstock to the desired point.

3.Tighten the two lock handles.

G9969 Radial Drill Press

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Model G9969 Radial Drill Press Page Table of Contents Foreword IntroductionContact Info Identification Machine Data Sheet 39-1/2 Safety G9969 Radial Drill Press Safety for Drill Presses Circuit Requirements 110/220V OperationAmperage Draw Circuit RequirementsGrounding Extension Cords110V Operation 220V OperationSET UP Set Up SafetyItems Needed for Set Up UnpackingClean Up InventoryBox 1 Figure Qty Other Components and Hardware QtyHardware Recognition Chart Site Considerations MountingTo install the column on the base ColumnHeadstock Bracket Components and Hardware Needed QtyTo install the headstock HeadstockTo install a light bulb in the drill press To install the downfeed handlesDownfeed Handles Belt Cover Knob Drill Chuck & Arbor To assemble the drill chuck and mount it to the spindleTest Run To test run your machineOperation Safety Safety Switch Key To install a drill bitOperations Changing BitsTo remove a drill bit Arbor RemovalTo remove the drill chuck and arbor Basic Drilling Operations Choosing Speeds Using the Drill Bit Speed ChartLubrication Suggestions Changing Speeds To change speedsTo set the depth stop Depth StopTo set the spindle return distance Headstock Adjustment Headstock Height & Column RotationHeadstock Tilt Headstock SwivelG5753-Drill Press Vise AccessoriesH1300 H1298 G7984 H2347 H0736 Maintenance Service About ServiceTroubleshooting Symptom Possible Cause Possible SolutionDrill Press Operations Depth Stop Feed Shaft Spring Calibration To calibrate the depth stopLoosening cover and jam nut G9969 Switch Wiring Electrical ComponentsWiring Diagram Parts Breakdown Parts List DescriptionParts List and Label Placement Warranty and Returns Page Page
Top Page Image Contents