Hitachi Koki USA DS 14DVF, DS 9DVF, DS 12DVF instruction manual Tightening torque adjustment

Page 19

English

mark

Black line

Fig. 10

CAUTION:

⬤The cap cannot be set between the numbers “1, 3, 5 ... 22” or the black dot.

⬤Do not use with the cap set at the black line between the number “22” and the drill mark “”. Doing so may cause damage. (See Fig. 10)

6.Tightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity to the screw diameter. When too strong power is used, the screw head may be broken or be injured.

Be sure to adjust the cap position according to the screw diameter.

(2) Tightening torque indication (See Fig. 9)

The tightening torque differs depending on the type of screw and the material being tightened.

The unit indicates the tightening torque with the numbers “1, 3, 5 ... 22” on the cap, and a black dot. The tightening torque at position “1” is the weakest and the torque is strongest at the highest number.

(3) Adjusting the tightening torque (See Fig. 9)

Rotate the cap and line up the numbers “1, 3, 5, ... 22” on the cap, or the black dot, with the triangle mark on the outer body. Adjust the cap in the weak or the strong torque direction according to the torque you need.

CAUTION:

⬤The motor rotation may be locked to cease while the unit is used as drill. While operating the driver drill, take care not to lock the motor.

⬤When setting the shift knob to “HIGH” (high speed) and the position of the cap is “17” to “22”, it may happen that the clutch does not engaged and that the motor is locked. In such a case, please set the shift knob to “LOW” (low speed).

⬤If the motor is locked, immediately turn the power off. If the motor is locked for a while, the motor or battery may be burnt.

⬤Too long hammering may cause the screw broken due to excessive tightening.

⬤A buzzing noise is produced when the motor is about to rotate; This is only a noise, not a machine failure.

19

Image 19

Contents Variable speed AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules for ALL Battery Operated Tools SafetyEnglish Specific Safety Rules and Symbols Never use a tool which is defective or operating abnormally Carefully handle power toolsDo not wipe plastic parts with solvent Important Safety Instructions for Battery Charger English Make Them Available to Other Users Owners of this Tool Disposal of the Exhausted BatteryCordless Driver Drill Functional DescriptionModel Name of PartsBattery Charger UC9SD, UC12SD and UC14SD Battery Charger SpecificationsCharging Method Assembly and OperationRemoval and Installation Method of Battery ApplicationsDisconnect battery charger from the receptacle Insert the battery to the battery chargerBefore USE Remove the battery from the battery chargerMounting and dismounting of the bit OperationConfirm the cap position see Fig Change rotation speedTightening torque adjustment Scope and Suggestions for Uses HOW to Select Tightening TorqueMaintenance and Inspection Standard Accessories AccessoriesOptional ACCESSORIES.....sold separately Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéConserver CES Instructions SecuriteAvertissement Lire et coxmprendre toutes les instructions Avertissement Regles DE Securite Specifiques ET Symboles Ne pas essuyer les parties en plastique avec du solvant Manipuler l’outil motorisé avec précautionIntensité nominale d’entrée CA ampères Français Mise AU Rebut D’UNE Batterie Usée Perceuse-visseuse à batterie FDS9DVA et FDS12DVA Description FonctionnelleModele NOM DES PartiesChargeur de batterie UC9SD, UC12SD et UC14SD Chargeur de batterie Perceuse-visseuse à batterieUtilisations Méthode DE Retrait ET D’INSTALLATION DE LA BatterieMéthode DE Recharge Brancher la fiche du chargeur de batterie dans la prise Insérer la batterie dans le chargeur de batterieRecharge Retirer la batterie du chargeur de batterie PrecautionAvant L’UTILISATION Débrancher le chargeur de batterie de la prisePose et dépose du foret UtilisationVérification de la position du capuchon. Voir Fig Changement de vitesse de rotationRéglage du couple de serrage Sélection DU Couple DE Serrage Plage D’UTILISATION ET SuggestionsEntretien ET Inspection Accessoires Standard AccessoiresAccessoires EN OPTION.....vendus séparément Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadGuarde Estas Instrucciones SeguridadAdvertencia Lea y entienda todas las instrucciones Advertencia Maneje correctamente la herramienta Normas Y Símbolos Específicos DE SeguridadNo toque Nunca las piezas móviles Utilice la herramienta correctaNo limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricas100 150 Español Eliminación DE LAS Baterías Agotadas Taladro atornillador a batería DS9DVF and DS12DVF Descripción FuncionalModelo NomenclaturaCargador de baterías UC9SD, UC12SD y UC14SD Taladro atornillador a batería EspecificacionesCargador de baterías Método DE Carga Montaje Y OperaciónAplicaciones Método DE Extracción E Instalación DE LA BateríaCarga Inserte la batería en el cargador de bateríasPrecaución Antes DE LA UtilizaciónDesconecte el cargador de baterías del tomacorriente Extraiga la batería del cargador de bateríasMontaje y desmontaje de la broca OperaciónPrecaucion Confirmar la posición de la cubierta Ver la Fig Cambio de velocidad de rotaciónPrecauciones Ajuste del par de aprieteForma DE Seleccionar EL PAR DE Apriete Alcance Y Sugerencias Para LA UtilizaciónEspañol Mantenimiento E Inspección Accesorios Estándar AccessoriosAccesorios OPCIONALES.....de venta por separado UC9SD DS12DVF English Page Page Hitachi Koki Canada Co