Hitachi Koki USA DS 9DVF, DS 14DVF, DS 12DVF instruction manual Maintenance and Inspection

Page 21

English

MAINTENANCE AND INSPECTION

CAUTION: Pull out battery before doing any inspection or maintenance.

1.Checking the condition of the bit.

The bits should be checked regularly. If worn or broken bits can slip or decrease the efficiency of the motor and burn it out.

Replace worn bits with new ones.

CAUTION: If you use a driver bit of which point is worn or broken, it will be dangerous since it slips. So replace it with a new one.

2.Check the Screws

Loose screws are dangerous. Regularly inspect them and make sure they are tight.

CAUTION: Using this power tool with loosened, screws is extremely dangerous.

3.Check for Dust

Dust may be removed with a soft cloth or a cloth dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner, for they may damage the plastics.

4.Storage

Storing in a place below 104°F (40°C) and out of the reach of children.

5.Service and repairs

All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.

6.Service parts list

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

21

Image 21
Contents Variable speed AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules for ALL Battery Operated Tools SafetyEnglish Specific Safety Rules and Symbols Carefully handle power tools Never use a tool which is defective or operating abnormallyDo not wipe plastic parts with solvent Important Safety Instructions for Battery Charger English Make Them Available to Other Users Owners of this Tool Disposal of the Exhausted BatteryModel Functional DescriptionName of Parts Cordless Driver DrillBattery Charger UC9SD, UC12SD and UC14SD Battery Charger SpecificationsRemoval and Installation Method of Battery Assembly and OperationApplications Charging MethodDisconnect battery charger from the receptacle Insert the battery to the battery chargerBefore USE Remove the battery from the battery chargerMounting and dismounting of the bit OperationConfirm the cap position see Fig Change rotation speedTightening torque adjustment Scope and Suggestions for Uses HOW to Select Tightening TorqueMaintenance and Inspection Standard Accessories AccessoriesOptional ACCESSORIES.....sold separately Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéSecurite Conserver CES InstructionsAvertissement Lire et coxmprendre toutes les instructions Avertissement Regles DE Securite Specifiques ET Symboles Ne pas essuyer les parties en plastique avec du solvant Manipuler l’outil motorisé avec précautionIntensité nominale d’entrée CA ampères Français Mise AU Rebut D’UNE Batterie Usée Modele Description FonctionnelleNOM DES Parties Perceuse-visseuse à batterie FDS9DVA et FDS12DVAChargeur de batterie UC9SD, UC12SD et UC14SD Chargeur de batterie Perceuse-visseuse à batterieMéthode DE Retrait ET D’INSTALLATION DE LA Batterie UtilisationsMéthode DE Recharge Insérer la batterie dans le chargeur de batterie Brancher la fiche du chargeur de batterie dans la priseRecharge Avant L’UTILISATION PrecautionDébrancher le chargeur de batterie de la prise Retirer la batterie du chargeur de batteriePose et dépose du foret UtilisationVérification de la position du capuchon. Voir Fig Changement de vitesse de rotationRéglage du couple de serrage Sélection DU Couple DE Serrage Plage D’UTILISATION ET SuggestionsEntretien ET Inspection Accessoires Standard AccessoiresAccessoires EN OPTION.....vendus séparément Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad Guarde Estas InstruccionesAdvertencia Lea y entienda todas las instrucciones Advertencia No toque Nunca las piezas móviles Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricas100 150 Español Eliminación DE LAS Baterías Agotadas Modelo Descripción FuncionalNomenclatura Taladro atornillador a batería DS9DVF and DS12DVFCargador de baterías UC9SD, UC12SD y UC14SD Especificaciones Taladro atornillador a bateríaCargador de baterías Aplicaciones Montaje Y OperaciónMétodo DE Extracción E Instalación DE LA Batería Método DE CargaCarga Inserte la batería en el cargador de bateríasDesconecte el cargador de baterías del tomacorriente Antes DE LA UtilizaciónExtraiga la batería del cargador de baterías PrecauciónOperación Montaje y desmontaje de la brocaPrecaucion Confirmar la posición de la cubierta Ver la Fig Cambio de velocidad de rotaciónPrecauciones Ajuste del par de aprieteForma DE Seleccionar EL PAR DE Apriete Alcance Y Sugerencias Para LA UtilizaciónEspañol Mantenimiento E Inspección Accesorios Estándar AccessoriosAccesorios OPCIONALES.....de venta por separado UC9SD DS12DVF English Page Page Hitachi Koki Canada Co