Hitachi DS 14DMR, DS 18DMR instruction manual Disconnect battery charger from the receptacle

Page 16

English

(2)Regarding the temperature of the rechargeable battery

The temperatures for rechargeable batteries are as shown in the table below, and batteries that have become hot should be cooled for a while before being recharged.

Table 3 Recharging of batteries that have become hot

Rechargeable batteries

Temperatures at which the battery can be recharged

 

 

EB14B

23°F—140°F (–5°C—60°C)

 

 

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5.Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

●When the battery charger has been continuosly used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging.

●If the battery is rechraged when it is warm due to battery use or exposure to sunlight, the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

●When the pilot lamp flickers in red (at 0.2–second intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer

(1)Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.

(2)Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Advertencia AvertissementModel Variable speed Cordless Driver Drill Contents Important Safety Information Meanings of Signal WordsSafety General Safety Rules for ALL Battery Operated ToolsEnglish Specific Safety Rules and Symbols Never use a tool which is defective or operating abnormally Carefully handle power toolsDo not wipe plastic parts with solvent Important Safety Instructions for Battery Charger English Disposal of the Exhausted Battery Make Them Available to Other Users Owners of this ToolFunctional Description ModelName of Parts Cordless Driver Drill DS14DMR and DS18DMRBattery Charger Specifications Cordless Driver DrillAssembly and Operation Removal and Installation Method of BatteryApplications Charging MethodInsert the battery to the battery charger Insert the plug of battery charger into the receptacleCharging Remove the battery from the battery charger Disconnect battery charger from the receptacleHow to make the batteries perform longer Battery Charge Time Lamp Status Lamp UC24YJ Battery overheated. Unable to charge Using the light equipped hook Revitalizing the battery trickle rechargeBefore USE OperationEnglish Battery leakage, rust or malfunction Failure to observe the following can resultPosition the plus + and minus terminals batteries Correctly Replace both batteries at the same time. DoInstalling/Removing the side handle Using the bit holderMounting and dismounting the bit Automatic spindle-lock mechanism Change rotation speedTightening torque adjustment Confirm the cap position See FigScope and Suggestions for Uses HOW to Select Tightening Torque Maintenance and Inspection Service and repairs Disposal of the exhausted battery StorageCheck for Dust Accessories Standard AccessoriesOptional ACCESSORIES.....sold separately Battery EB14B Battery EB1830HL For DS14DMR For DS18DMRInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Conserver CES InstructionsAvertissement Lire et coxmprendre toutes les instructions Sécurité personnelleAvertissement Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesManipuler l’outil motorisé avec précaution Ne pas essuyer les parties en plastique avec du solvantIntensité nominale d’entrée CA ampères Français Mise AU Rebut D’UNE Batterie Usée Description Fonctionnelle ModeleNOM DES Parties Perceuse-visseuse à batterie DS14DMR et DS18DMRChargeur de batterie Perceuse-visseuse à batterie Utilisations Méthode DE Retrait ET D’INSTALLATION DE LA BatterieMéthode DE Recharge Insérer la batterie dans le chargeur de batterie Brancher la fiche du chargeur de batterie dans la priseRecharge Débrancher le chargeur de batterie de la prise Retirer la batterie du chargeur de batteriePrise Brancher la fiche du chargeur de batterie dans laComment prolonger la durée de vie des batteries Français Revitalisation de la batterie recharge d’entretient Utilisation Avant L’UTILISATIONUtilisation du crochet muni d’un éclairage Modification de la position du crochet Utilisation du porte-foret Installation/retrait de la poignée latéraleLe foret pourrait tomber et provoquer des blessures Pose et dépose du foret Changement de vitesse de rotation Vérification de la position du capuchon Voir Fig 10. Réglage du couple de serragePlage D’UTILISATION ET Suggestions Sélection DU Couple DE SerrageEntretien ET Inspection Vérifier l’état de la mècheVérifier les vis Entretien du moteurRemplacement d’un balai en carbone Vérifier s’il y a de la poussièreMise au rebut d’une batterie usée RangementAccessoires Accessoires StandardAccessoires EN OPTION.....vendus séparément Batterie EB14B Batterie EB1830HL Pour DS14DMR Pour DS18DMRInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónGuarde Estas Instrucciones SeguridadAdvertencia Lea y entienda todas las instrucciones Advertencia Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolvente25 7,5 100 150 Español Eliminación DE LAS Baterías Agotadas Modelo Descripción FuncionalNomenclatura Cargador de baterías Especificaciones Taladro atornillador a bateríaMontaje Y Operación AplicacionesMétodo DE Extracción E Instalación DE LA Batería Método DE CargaInserte la batería en el cargador de baterías CargaDesconecte el cargador de baterías del tomacorriente Extraiga la batería del cargador de bateríasForma de hacer que las baterías duren más Minutos Rojo Finalizar Carga Desconecte el cargador de baterías del tomacorriente Antes DE LA Utilización OperaciónUso del gancho equipado con luz Revitalización de la batería recarga hábilResorte Uso del portabrocas Instalación/desmontaje del asa lateral Montaje y desmontaje de la brocaMecanismo de bloqueo del husillo Cambio de velocidad de rotaciónConfirmar la posición de la cubierta Ver la Fig Alcance Y Sugerencias Para LA Utilización Ajuste del par de aprieteForma DE Seleccionar EL PAR DE Apriete Mantenimiento E Inspección Comprobación de las condiciones de la brocaComprobación de los tornillos Mantenimiento de motorReemplazar el carbón de contacto Comprobación del polvoEliminación de las baterías agotadas AlmacenamientoAccesorios Accesorios EstándarAccesorios OPCIONALES.....de venta por separado Battería EB14B Battería EB1830HL Para DS14DMR Para DS18DMRHitachi Koki Canada Co
Top Page Image Contents