Dell MD3200, MD3220 manual ISCSI Configuration Worksheet

Page 32

Table 4-1. Standard Terminology Used in iSCSI Configuration

Term

Definition

 

 

iSCSI initiator

The iSCSI-specific software installed on the

 

host server that controls communications

 

between the host server and the storage array.

iSCSI host port

The iSCSI port (two per controller) on the

 

storage array.

iSNS (Microsoft Internet Storage

An automated discovery, management and

Naming Service)

configuration Storage Naming Service) tool

 

used by some iSCSI devices.

Management station

The system from which you manage your

 

host server/storage array configuration.

Storage array

The enclosure containing the storage data

 

accessed by the host server.

Target

An iSCSI port on the storage array that

 

accepts and responds to requests from the

 

iSCSI initiator installed on the host server.

 

 

iSCSI Configuration Worksheet

The "IPv4 Settings—Worksheet" on page 33 and "IPv6 Settings—Worksheet" on page 34 helps you plan your configuration. Recording host server and storage array IP addresses at a single location enables you to configure your setup faster and more efficiently.

"Guidelines For Configuring Your Network For iSCSI" on page 40 provides general network setup guidelines for both Microsoft Windows and Linux environments. It is recommended that you review these guidelines before completing the worksheet.

32

Post Installation Tasks

Image 32
Contents Deployment Guide Dell Inc Contents ISCSI Configuration Worksheet Configuring iSCSI on Your Storage ArrayDiscover the Storage Array Out-of-band Management Only Locating Your System Service TagWindows Load Balance Policy Configure the iSCSI Ports on Configure Host Access Understanding Chap AuthenticationConfigure Chap Authentication on Configuring Target Chap Authentication onManagement Station Requirements IntroductionSystem Requirements Introduction to Storage Arrays Introduction Introduction Hardware Installation Planning the Storage ConfigurationConnecting the Storage Array Cabling the Storage ArrayRedundant and Non-Redundant Configurations Single Controller ConfigurationsTwo Hosts Connected to a Single Controller Four Hosts Connected to a Single Controller Dual Controller Configurations Two Hosts Connected to Two ControllersFour Hosts Connected to Two Controllers Four Hosts Connected to Two Controllers Eight Hosts Connected to Two Controllers Four Cluster Nodes Connected to Two Controllers Four Cluster Nodes Connected to Two Controllers Cabling PowerVault MD1200 Series Expansion Enclosures Hardware Installation Hardware Installation Click Advanced→ Maintanence→ Download→ EMM Firmware Hardware Installation Installing PowerVault MD Storage Software Graphical Installation Recommended Select Install MD Storage SoftwareConsole Installation Silent InstallationUpgrading PowerVault MD Storage Software Before You Begin Post Installation TasksStandard Terminology Used in iSCSI Configuration Definition ISCSI Configuration Worksheet IPv4 Settings-Worksheet SecretIPv6 Settings-Worksheet Mutual Chap Target ChapConfiguring iSCSI on Your Storage Array Host Server Vs. Storage Array ManagerStorage Array Configuration Before Starting the Configuration Process Configure the Storage Array Using Mdcu Post Connection Establishment StepsGuidelines For Configuring Your Network For iSCSI Microsoft Windows Host SetupUsing a Dhcp server Using static IP addressingUsing a DNS server Using a Wins ServerUsing a Static IP Address Linux Host SetupUsing Dhcp HWADDR=XXXXXXXXXXXX GATEWAY=192.168.1.1 Post Installation Tasks Uninstalling PowerVault MD Storage Software Uninstalling MD Storage Software From WindowsUninstalling MD Storage Software From Linux Run the file Uninstall Dell MD Storage Software.exeContacting Dell Locating Your System Service TagGetting Help Documentation Feedback Round Robin With Subset Appendix-Load BalancingWindows Load Balance Policy Least Queue Depth With Subset Changing Load Balance Policies in Windows SeverSetting Load Balance Policies in Linux Appendix-Load Balancing Table B-1. Host Server Vs. Storage Array Appendix-Manual Configuration of iSCSIArray Using MD Storage Manager Discover the Storage Array Out-of-band Management Only Default Management IPv4 Port SettingsDefault Management IPv6 Port Settings Automatic Storage Array Discovery Setting Up the Array Manual Storage Array DiscoveryConfigure the iSCSI Ports on the Storage Array Table B-2. Initial Setup Tasks Dialog Box PurposeAppendix-Manual Configuration of iSCSI Perform Target Discovery From the iSCSI Initiator Set the iSCSI initiator service to start automatically Configure Host Access Understanding Chap Authentication What is CHAP?Target Chap Mutual ChapConfigure Chap Authentication on the Storage Array Optional Configuring Target Chap Authentication on the Storage ArrayChap Definitions Table B-3. Chap Types Defined DescriptionConfiguring Mutual Chap Authentication on the Storage Array Table B-4. Chap Setting Option DescriptionConfigure Chap Authentication on the Host Server Optional Add the target portal with Chap defined Discovery.sendtargets.auth.authmethod = Chap Appendix-Manual Configuration of iSCSI Connect to the Target Storage Array From the Host Server Local Adapter-Must be set to Microsoft iSCSI InitiatorIf you are using Windows Server 2008 Core Version TCPPortNumberOfTargetPortal is Optional Set Up In-Band Management Appendix-Manual Configuration of iSCSI Appendix-Manual Configuration of iSCSI
Related manuals
Manual 260 pages 11.3 Kb Manual 272 pages 61.39 Kb Manual 22 pages 36.51 Kb