Dell MD3220, MD3200 manual Appendix-Manual Configuration of iSCSI

Page 73

NOTE: Configure the management station you are using for network communication to the same IP subnet as the PowerVault MD36x0i host ports.

1Establish an iSCSI session to the PowerVault MD3600i RAID storage array.

2Restart the SMagent service.

3Launch MDSM.

If this is the first storage array to be set up for management, the Add New Storage Array window is displayed. Otherwise, click New.

4Select Manual and click OK.

5Select In-band management and enter the host server name(s) or IP address(es) of the host server that is running the MD Storage Manager software.

6Click Add.

In-band management should now be successfully configured.

Appendix—Manual Configuration of iSCSI

73

Image 73

Contents Deployment Guide Dell Inc Contents Configuring iSCSI on Your Storage Array ISCSI Configuration WorksheetWindows Load Balance Policy Locating Your System Service TagDiscover the Storage Array Out-of-band Management Only Configure Host Access Understanding Chap Authentication Configure the iSCSI Ports onConfigure Chap Authentication on Configuring Target Chap Authentication onSystem Requirements IntroductionManagement Station Requirements Introduction to Storage Arrays Introduction Introduction Planning the Storage Configuration Hardware InstallationCabling the Storage Array Connecting the Storage ArraySingle Controller Configurations Redundant and Non-Redundant ConfigurationsTwo Hosts Connected to a Single Controller Four Hosts Connected to a Single Controller Two Hosts Connected to Two Controllers Dual Controller ConfigurationsFour Hosts Connected to Two Controllers Four Hosts Connected to Two Controllers Eight Hosts Connected to Two Controllers Four Cluster Nodes Connected to Two Controllers Four Cluster Nodes Connected to Two Controllers Cabling PowerVault MD1200 Series Expansion Enclosures Hardware Installation Hardware Installation Click Advanced→ Maintanence→ Download→ EMM Firmware Hardware Installation Installing PowerVault MD Storage Software Select Install MD Storage Software Graphical Installation RecommendedSilent Installation Console InstallationUpgrading PowerVault MD Storage Software Standard Terminology Used in iSCSI Configuration Definition Post Installation TasksBefore You Begin ISCSI Configuration Worksheet Secret IPv4 Settings-WorksheetMutual Chap Target Chap IPv6 Settings-WorksheetConfiguring iSCSI on Your Storage Array Manager Host Server Vs. Storage ArrayStorage Array Configuration Before Starting the Configuration Process Post Connection Establishment Steps Configure the Storage Array Using MdcuMicrosoft Windows Host Setup Guidelines For Configuring Your Network For iSCSIUsing a Dhcp server Using static IP addressingUsing a Wins Server Using a DNS serverUsing Dhcp Linux Host SetupUsing a Static IP Address HWADDR=XXXXXXXXXXXX GATEWAY=192.168.1.1 Post Installation Tasks Uninstalling MD Storage Software From Windows Uninstalling PowerVault MD Storage SoftwareRun the file Uninstall Dell MD Storage Software.exe Uninstalling MD Storage Software From LinuxGetting Help Locating Your System Service TagContacting Dell Documentation Feedback Windows Load Balance Policy Appendix-Load BalancingRound Robin With Subset Changing Load Balance Policies in Windows Sever Least Queue Depth With SubsetSetting Load Balance Policies in Linux Appendix-Load Balancing Array Using MD Storage Manager Appendix-Manual Configuration of iSCSITable B-1. Host Server Vs. Storage Array Default Management IPv6 Port Settings Default Management IPv4 Port SettingsDiscover the Storage Array Out-of-band Management Only Automatic Storage Array Discovery Manual Storage Array Discovery Setting Up the ArrayTable B-2. Initial Setup Tasks Dialog Box Purpose Configure the iSCSI Ports on the Storage ArrayAppendix-Manual Configuration of iSCSI Perform Target Discovery From the iSCSI Initiator Set the iSCSI initiator service to start automatically Configure Host Access What is CHAP? Understanding Chap AuthenticationTarget Chap Mutual ChapConfiguring Target Chap Authentication on the Storage Array Configure Chap Authentication on the Storage Array OptionalChap Definitions Table B-3. Chap Types Defined DescriptionTable B-4. Chap Setting Option Description Configuring Mutual Chap Authentication on the Storage ArrayConfigure Chap Authentication on the Host Server Optional Add the target portal with Chap defined Discovery.sendtargets.auth.authmethod = Chap Appendix-Manual Configuration of iSCSI Local Adapter-Must be set to Microsoft iSCSI Initiator Connect to the Target Storage Array From the Host ServerIf you are using Windows Server 2008 Core Version TCPPortNumberOfTargetPortal is Optional Set Up In-Band Management Appendix-Manual Configuration of iSCSI Appendix-Manual Configuration of iSCSI

Related manuals

Manual 260 pages 11.3 Kb

Manual 272 pages 61.39 Kb

Manual 22 pages 36.51 Kb