Bostitch N400S Maintaining the Pneumatic Tool, Replacement Parts, Assembly Procedure for Seals

Page 10

MAINTAINING THE PNEUMATIC TOOL

When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.

CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand. Also the edges of the spring are very thin and could cut. Care must also be taken to insure no permanent kinks are put in the spring as this will reduce the springs force.

REPLACEMENT PARTS:

BOSTITCH replacement parts are recommended. Do not use modified parts or parts which will not give equivalent performance to the original equipment.

ASSEMBLY PROCEDURE FOR SEALS:

When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE or equivalent on all “O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of BOSTITCH Air Tool Lubricant through the air line fitting before testing.

AIR SUPPLY-PRESSURE AND VOLUME:

Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air supply from the tool to the supply source for restrictive connectors, swivel fittings, low points containing water and anything else that would prevent full volume flow of air to the tool.

10

Image 10
Contents N400S Introduction IndexLoading Tool Safety InstructionsAIR Supply and Connections OperationN400S Tool Specifications Lubrication Close Magazine Loading the N400SLoad Nails Pusher release tabWhen using the framing contact arm Fastener Depth Control AdjustmentTo Adjust the Fastener Depth Control Directional Exhaust DeflectorSequential Trip Operation Gray Trigger Tool OperationBefore Handling or Operating this Tool Contact Trip Conventional Operation Black TriggerSequential Trip Operation Tool Operation CheckContact Trip Operation AIR SUPPLY-PRESSURE and Volume Replacement PartsAssembly Procedure for Seals Maintaining the Pneumatic ToolTrouble Shooting Problem Cause CorrectionÍndice IntroducciónNota Carga DE LA Herramienta Instrucciones DE SeguridadSuministro DE Aire Y Conexiones FuncionamientoEspecificaciones DE LA Herramienta N400S Lubricación Cierre el depósito Carga DE LA Herramienta N400SCargue los clavos Lengüeta liberación del empujadorExtracción DE Clavos Ajuste DEL Control DE Profundidad DEL ClavoDeflector DE Escape Direccional Para Ajustar EL Control DE Profundidad DEL ClavoAntes DE Manipular U Operar Esta Herramienta Funcionamiento DE LA HerramientaFuncionamiento DEL Disparo Secuencial Gatillo Gris Funcionamiento DEL Disparo Secuencial Revisión Funcional DE LA HerramientaFuncionamiento DEL Disparo DE Contacto Piezas DE Repuesto Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Procedimiento DE Ensamblaje Para LOS SellosSolución DE Problemas El vástago de la válvula de disparo Tiene fuga de aireRemarque Garantie Limitée É.-U. et Canada seulementAlimentation EN AIR ET Connexions Maintenance DE L’OUTILInstructions DE Sécurité Chargement DE L’OUTILCaractéristiques Techniques DES Outils DE LA N400S Lubrification Fermez le magasin Chargement DES Outils DE LA N400SChargez les clous Taquet de verrouillage du pousseurRetrait DES Clous Commande DE Réglage DE Profondeur DE FixationDéflecteur Déchappement Directionnel Pour Régler LA Profondeur DE FixationUtilisation Fonctionnement DE L’OUTILDéclenchement Séquentiel Gâchette Grise Utilisation DU Déclencheur Séquentiel Utilisation DE L’OUTIL SuiteVérification DE L’ÉTAT DE Marche DE L’OUTIL Fonctionnement DE LA Butée DE DéclenchementPièces DE Rechange Maintenance DE L’OUTIL PneumatiquePression ET Volume DE L’ALIMENTATION D’AIR Procédure DE Montage DES JointsDépannage Remplacez les joints toriques/jointsNotas Y Registros Remarques ET Rapports

171430REVA, N400S specifications

The Bostitch N400S,171430REVA is a high-performance pneumatic nailer designed for professionals in the construction and woodworking industries. Known for its reliability and versatility, this tool is ideal for various applications, including framing, roofing, and flooring. This article explores the main features, technologies, and characteristics that set the N400S apart from other nailers in the market.

One of the standout features of the Bostitch N400S is its ability to accommodate a wide range of nail sizes. It can handle nails measuring from 1 inch to 2 inches, providing users with the flexibility needed for various projects. The tool employs a one-handed operation design, allowing users to easily adjust the depth of drive without needing additional tools. This feature helps in achieving consistent results across different materials and applications.

The N400S is equipped with advanced technology to enhance user experience and performance. It boasts a powerful and efficient motor that delivers a high degree of performance while minimizing misfires. This is particularly beneficial in fast-paced environments where time is of the essence. Additionally, the nailer features a lightweight aluminum construction, making it easy to handle without causing operator fatigue during prolonged use.

Another notable characteristic of the N400S is its integrated air filter and anti-dust cap. These features help to keep the internal mechanisms clean and free of debris, ensuring optimal performance over time. The tool's rear exhaust directs air away from the user and the work surface, providing a cleaner work environment.

Safety is also a priority with the Bostitch N400S. It includes a sequential firing mode that enhances precision while reducing the risk of accidental discharge. The rubber grip handle provides a comfortable and secure hold, further enhancing control during operation.

In conclusion, the Bostitch N400S,171430REVA nailer stands out for its robust design, user-friendly features, and efficient performance. Its compatibility with various nail sizes, combined with advanced technologies and safety features, makes it a valuable addition to any professional's toolkit. Whether tackling framing jobs or more detailed woodworking tasks, the N400S is engineered to deliver outstanding results and reliability, making it an ideal choice for contractors and DIY enthusiasts alike.