Bostitch 171430REVA, N400S manual Trouble Shooting, Problem Cause Correction

Page 11

 

 

TROUBLE SHOOTING

PROBLEM

CAUSE

CORRECTION

Trigger valve housing leaks air

O-ring cut or cracked

Replace O-ring

Trigger valve stem leaks air

O-ring/seals cut or cracked

Replace trigger valve assembly

Frame/nose leaks air

Loose nose screws

Tighten and recheck

 

O-ring or Gasket is cut or cracked

Replace O-ring or gasket

 

Bumper cracked/worn

Replace bumper

Frame/cap leaks air

Damaged gasket or seal

Replace gasket or seal

 

Cracked/worn head valve bumper

Replace bumper

 

Loose cap screws

Tighten and recheck

Failure to cycle

Air supply restriction

Check air supply equipment

 

Tool dry, lack of lubrication

Use BOSTITCH Air Tool Lubricant

 

Worn head valve O-rings

Replace O-rings

 

Broken cylinder cap spring

Replace cylinder cap spring

 

Head valve stuck in cap

Disassemble/Check/Lubricate

Lack of power; slow to cycle

Tool dry, lacks lubrication

Use BOSTITCH Air Tool Lubricant

 

Broken cylinder cap spring

Replace cap spring

 

O-rings/seals cut or cracked

Replace O-rings/seals

 

Exhaust blocked

Check bumper, head valve spring, muffler

 

Trigger assembly worn/leaks

Replace trigger assembly

 

Dirt/tar build up on driver

Disassemble nose/driver to clean

 

Cylinder sleeve not seated correctlyon bottom bumper Disassemble to correct

 

Head valve dry

Disassemble/lubricate

 

Air pressure too low

Check air supply equipment

Skipping fasteners; intermittent feed

Worn bumper

Replace bumper

 

Tar/dirt in driver channel

Disassemble and clean nose and driver

 

Air restriction/inadequate air flow through

 

 

quick disconnect socket and plug

Replace quick disconnect fittings

 

Worn piston O-ring

Replace O-ring, check driver

 

Tool dry, lacks lubrication

Use BOSTITCH Air Tool Lubricant

 

Damaged pusher spring

Replace spring

 

Low air pressure

Check air supply system to tool

 

Loose magazine nose screws

Tighten all screws

 

Fasteners too short for tool

Use only recommended fasteners

 

Bent fasteners

Discontinue using these fasteners

 

Wrong size fasteners

Use only recommended fasteners

 

Leaking head cap gasket

Tighten screws/replace gasket

 

Trigger valve O-ring cut/worn

Replace O-ring

 

Broken/chipped driver

Replace driver (check piston O-ring)

 

Dry/dirty magazine

Clean/lubricate use BOSTITCH Air Tool Lubricant

 

Worn magazine

Replace magazine

Fasteners jam in tool

Driver channel worn

Replace nose/check door

 

Wrong size fasteners

Use only recommended fasteners

 

Bent fasteners

Discontinue using these fasteners

 

Loose magazine/nose screws

Tighten all screws

 

Broken/chipped driver

Replace driver

Fastener misses

Broken / chipped guide

Replace guide

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents N400S Index IntroductionOperation Safety InstructionsAIR Supply and Connections Loading ToolN400S Tool Specifications Lubrication Pusher release tab Loading the N400SLoad Nails Close MagazineDirectional Exhaust Deflector Fastener Depth Control AdjustmentTo Adjust the Fastener Depth Control When using the framing contact armContact Trip Conventional Operation Black Trigger Tool OperationBefore Handling or Operating this Tool Sequential Trip Operation Gray TriggerContact Trip Operation Tool Operation CheckSequential Trip Operation Maintaining the Pneumatic Tool Replacement PartsAssembly Procedure for Seals AIR SUPPLY-PRESSURE and VolumeProblem Cause Correction Trouble ShootingNota IntroducciónÍndice Funcionamiento Instrucciones DE SeguridadSuministro DE Aire Y Conexiones Carga DE LA HerramientaEspecificaciones DE LA Herramienta N400S Lubricación Lengüeta liberación del empujador Carga DE LA Herramienta N400SCargue los clavos Cierre el depósitoPara Ajustar EL Control DE Profundidad DEL Clavo Ajuste DEL Control DE Profundidad DEL ClavoDeflector DE Escape Direccional Extracción DE ClavosFuncionamiento DEL Disparo Secuencial Gatillo Gris Funcionamiento DE LA HerramientaAntes DE Manipular U Operar Esta Herramienta Funcionamiento DEL Disparo DE Contacto Revisión Funcional DE LA HerramientaFuncionamiento DEL Disparo Secuencial Procedimiento DE Ensamblaje Para LOS Sellos Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Piezas DE RepuestoEl vástago de la válvula de disparo Tiene fuga de aire Solución DE ProblemasGarantie Limitée É.-U. et Canada seulement RemarqueChargement DE L’OUTIL Maintenance DE L’OUTILInstructions DE Sécurité Alimentation EN AIR ET ConnexionsCaractéristiques Techniques DES Outils DE LA N400S Lubrification Taquet de verrouillage du pousseur Chargement DES Outils DE LA N400SChargez les clous Fermez le magasinPour Régler LA Profondeur DE Fixation Commande DE Réglage DE Profondeur DE FixationDéflecteur Déchappement Directionnel Retrait DES ClousDéclenchement Séquentiel Gâchette Grise Fonctionnement DE L’OUTILUtilisation Fonctionnement DE LA Butée DE Déclenchement Utilisation DE L’OUTIL SuiteVérification DE L’ÉTAT DE Marche DE L’OUTIL Utilisation DU Déclencheur SéquentielProcédure DE Montage DES Joints Maintenance DE L’OUTIL PneumatiquePression ET Volume DE L’ALIMENTATION D’AIR Pièces DE RechangeRemplacez les joints toriques/joints DépannageNotas Y Registros Remarques ET Rapports

171430REVA, N400S specifications

The Bostitch N400S,171430REVA is a high-performance pneumatic nailer designed for professionals in the construction and woodworking industries. Known for its reliability and versatility, this tool is ideal for various applications, including framing, roofing, and flooring. This article explores the main features, technologies, and characteristics that set the N400S apart from other nailers in the market.

One of the standout features of the Bostitch N400S is its ability to accommodate a wide range of nail sizes. It can handle nails measuring from 1 inch to 2 inches, providing users with the flexibility needed for various projects. The tool employs a one-handed operation design, allowing users to easily adjust the depth of drive without needing additional tools. This feature helps in achieving consistent results across different materials and applications.

The N400S is equipped with advanced technology to enhance user experience and performance. It boasts a powerful and efficient motor that delivers a high degree of performance while minimizing misfires. This is particularly beneficial in fast-paced environments where time is of the essence. Additionally, the nailer features a lightweight aluminum construction, making it easy to handle without causing operator fatigue during prolonged use.

Another notable characteristic of the N400S is its integrated air filter and anti-dust cap. These features help to keep the internal mechanisms clean and free of debris, ensuring optimal performance over time. The tool's rear exhaust directs air away from the user and the work surface, providing a cleaner work environment.

Safety is also a priority with the Bostitch N400S. It includes a sequential firing mode that enhances precision while reducing the risk of accidental discharge. The rubber grip handle provides a comfortable and secure hold, further enhancing control during operation.

In conclusion, the Bostitch N400S,171430REVA nailer stands out for its robust design, user-friendly features, and efficient performance. Its compatibility with various nail sizes, combined with advanced technologies and safety features, makes it a valuable addition to any professional's toolkit. Whether tackling framing jobs or more detailed woodworking tasks, the N400S is engineered to deliver outstanding results and reliability, making it an ideal choice for contractors and DIY enthusiasts alike.
Top Page Image Contents