N400S Tool Specifications

All screws and nuts are metric.

MODEL	TOOL	LENGTH	HEIGHT	WIDTH	WEIGHT
MODEL	ACTUATION	LENGTH	HEIGHT	WIDTH	WEIGHT

N400S	Sequential Trip with	19.5” (495mm)	15.5” (394mm)	5” (127mm)	7.7 lb. (3.5 kg.)
	Contact Trip Option
N400S-2	Sequential Trip	19.5” (495mm)	15.5” (394mm)	5” (127mm)	7.7 lb. (3.5 kg.)

FASTENER SPECIFICATIONS:

N400S: Uses a 28° wire collated stick nail in lengths of 2” to 4” (50 - 90mm) and shank diameters of .113” to .131” (2.8 - 3.3mm).

TOOL AIR FITTING:

This tool uses a 1/4” N.P.T. male plug. The inside diameter should be .275” (7mm) or larger. The fitting must be capable of discharging tool air pressure when disconnected from the air supply.

OPERATING PRESSURE:

70 to 120 p.s.i.g. (4.9 to 8.4 kg/cm2). Select the operating pressure within this range for best fastener performance.

DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.

AIR CONSUMPTION:

The N400S requires 7.5 cubic feet per minute (212 liters per minute) of free air to operate at the rate of 100 nails per minute, at 80 p.s.i. (5.6 kg/cm2). Take the actual rate at which the tool will be run to determine the amount of air required. For instance, if your fastener usage averages 50 nails per minute, you need 50% of the 7.5 c.f.m. (212 liters per minute) which is required to operate the tool at 100 nails per minute.

OPERATION

BOSTITCH OFFERS TWO MODES OF OPERATION FOR THIS TOOL.

SEQUENTIAL TRIP (Gray trigger):

The Sequential Trip requires the operator to hold the tool against the work surface before pulling the trigger. This makes accurate fastener placement easier, for instance on framing, toe nailing and crating applications.The Sequential Trip allows exact fastener placement without the possibility of driving a second fastener on recoil, as described under “Contact Trip”. The Sequential Trip Tool has a positive safety advantage because it will not accidentally drive a second fastener if the tool is contacted against the work – or anything else – while the operator is holding the trigger pulled.

CONTACT TRIP (Black trigger):

The common operating procedure on “Contact Trip” tools is for the operator to contact the work surface to actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is contacted. This will allow rapid fastener placement on many jobs, such as sheathing, decking and pallet assembly. All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip, and if unintentionally allowed to re-contact the work surface with the trigger still actuated (finger still holding trigger pulled) an unwanted second fastener will be driven.

MODEL IDENTIFICATION:

Refer to Operation Instructions on page 3 before proceeding to use this tool.

SEQUENTIAL TRIP					CONTACT TRIP
Identified by:					Identified by:
GRAY TRIGGER					BLACK TRIGGER

171430REVA, N400S specifications

The Bostitch N400S,171430REVA is a high-performance pneumatic nailer designed for professionals in the construction and woodworking industries. Known for its reliability and versatility, this tool is ideal for various applications, including framing, roofing, and flooring. This article explores the main features, technologies, and characteristics that set the N400S apart from other nailers in the market.

One of the standout features of the Bostitch N400S is its ability to accommodate a wide range of nail sizes. It can handle nails measuring from 1 inch to 2 inches, providing users with the flexibility needed for various projects. The tool employs a one-handed operation design, allowing users to easily adjust the depth of drive without needing additional tools. This feature helps in achieving consistent results across different materials and applications.

The N400S is equipped with advanced technology to enhance user experience and performance. It boasts a powerful and efficient motor that delivers a high degree of performance while minimizing misfires. This is particularly beneficial in fast-paced environments where time is of the essence. Additionally, the nailer features a lightweight aluminum construction, making it easy to handle without causing operator fatigue during prolonged use.

Another notable characteristic of the N400S is its integrated air filter and anti-dust cap. These features help to keep the internal mechanisms clean and free of debris, ensuring optimal performance over time. The tool's rear exhaust directs air away from the user and the work surface, providing a cleaner work environment.

Safety is also a priority with the Bostitch N400S. It includes a sequential firing mode that enhances precision while reducing the risk of accidental discharge. The rubber grip handle provides a comfortable and secure hold, further enhancing control during operation.

In conclusion, the Bostitch N400S,171430REVA nailer stands out for its robust design, user-friendly features, and efficient performance. Its compatibility with various nail sizes, combined with advanced technologies and safety features, makes it a valuable addition to any professional's toolkit. Whether tackling framing jobs or more detailed woodworking tasks, the N400S is engineered to deliver outstanding results and reliability, making it an ideal choice for contractors and DIY enthusiasts alike.