Bostitch 171430REVA manual Loading the N400S, Load Nails, Close Magazine, Pusher release tab

Page 6

LOADING THE N400S

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

TO PREVENT ACCIDENTAL INJURIES:

•Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected.

•Never point the tool at anyone else.

•Never engage in horseplay.

•Never pull the trigger unless nose is directed at the work.

•Always handle the tool with care.

•Do not pull the trigger or depress the trip mechanism while loading the tool.

1.Open the magazine:

Pull pusher back to engage the latch.

2.Load Nails:

Hold nailer down with magazine tilted downward. Insert stick of nails

3.Close Magazine:

Release pusher by first pulling back on the pusher and then pressing the pusher release tab. Slide pusher foreward against nails.

Pusher release tab.

NOTE: Use only nails recommended for use in BOSTITCH Framing nailers or nails which meet the BOSTITCH specifications.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents N400S Introduction IndexLoading Tool Safety InstructionsAIR Supply and Connections OperationN400S Tool Specifications Lubrication Close Magazine Loading the N400SLoad Nails Pusher release tabWhen using the framing contact arm Fastener Depth Control AdjustmentTo Adjust the Fastener Depth Control Directional Exhaust DeflectorSequential Trip Operation Gray Trigger Tool OperationBefore Handling or Operating this Tool Contact Trip Conventional Operation Black TriggerTool Operation Check Sequential Trip OperationContact Trip Operation AIR SUPPLY-PRESSURE and Volume Replacement PartsAssembly Procedure for Seals Maintaining the Pneumatic ToolTrouble Shooting Problem Cause CorrectionIntroducción ÍndiceNota Carga DE LA Herramienta Instrucciones DE SeguridadSuministro DE Aire Y Conexiones FuncionamientoEspecificaciones DE LA Herramienta N400S Lubricación Cierre el depósito Carga DE LA Herramienta N400SCargue los clavos Lengüeta liberación del empujadorExtracción DE Clavos Ajuste DEL Control DE Profundidad DEL ClavoDeflector DE Escape Direccional Para Ajustar EL Control DE Profundidad DEL ClavoFuncionamiento DE LA Herramienta Antes DE Manipular U Operar Esta HerramientaFuncionamiento DEL Disparo Secuencial Gatillo Gris Revisión Funcional DE LA Herramienta Funcionamiento DEL Disparo SecuencialFuncionamiento DEL Disparo DE Contacto Piezas DE Repuesto Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Procedimiento DE Ensamblaje Para LOS SellosSolución DE Problemas El vástago de la válvula de disparo Tiene fuga de aireRemarque Garantie Limitée É.-U. et Canada seulementAlimentation EN AIR ET Connexions Maintenance DE L’OUTILInstructions DE Sécurité Chargement DE L’OUTILCaractéristiques Techniques DES Outils DE LA N400S Lubrification Fermez le magasin Chargement DES Outils DE LA N400SChargez les clous Taquet de verrouillage du pousseurRetrait DES Clous Commande DE Réglage DE Profondeur DE FixationDéflecteur Déchappement Directionnel Pour Régler LA Profondeur DE FixationFonctionnement DE L’OUTIL UtilisationDéclenchement Séquentiel Gâchette Grise Utilisation DU Déclencheur Séquentiel Utilisation DE L’OUTIL SuiteVérification DE L’ÉTAT DE Marche DE L’OUTIL Fonctionnement DE LA Butée DE DéclenchementPièces DE Rechange Maintenance DE L’OUTIL PneumatiquePression ET Volume DE L’ALIMENTATION D’AIR Procédure DE Montage DES JointsDépannage Remplacez les joints toriques/jointsNotas Y Registros Remarques ET Rapports

171430REVA, N400S specifications

The Bostitch N400S,171430REVA is a high-performance pneumatic nailer designed for professionals in the construction and woodworking industries. Known for its reliability and versatility, this tool is ideal for various applications, including framing, roofing, and flooring. This article explores the main features, technologies, and characteristics that set the N400S apart from other nailers in the market.

One of the standout features of the Bostitch N400S is its ability to accommodate a wide range of nail sizes. It can handle nails measuring from 1 inch to 2 inches, providing users with the flexibility needed for various projects. The tool employs a one-handed operation design, allowing users to easily adjust the depth of drive without needing additional tools. This feature helps in achieving consistent results across different materials and applications.

The N400S is equipped with advanced technology to enhance user experience and performance. It boasts a powerful and efficient motor that delivers a high degree of performance while minimizing misfires. This is particularly beneficial in fast-paced environments where time is of the essence. Additionally, the nailer features a lightweight aluminum construction, making it easy to handle without causing operator fatigue during prolonged use.

Another notable characteristic of the N400S is its integrated air filter and anti-dust cap. These features help to keep the internal mechanisms clean and free of debris, ensuring optimal performance over time. The tool's rear exhaust directs air away from the user and the work surface, providing a cleaner work environment.

Safety is also a priority with the Bostitch N400S. It includes a sequential firing mode that enhances precision while reducing the risk of accidental discharge. The rubber grip handle provides a comfortable and secure hold, further enhancing control during operation.

In conclusion, the Bostitch N400S,171430REVA nailer stands out for its robust design, user-friendly features, and efficient performance. Its compatibility with various nail sizes, combined with advanced technologies and safety features, makes it a valuable addition to any professional's toolkit. Whether tackling framing jobs or more detailed woodworking tasks, the N400S is engineered to deliver outstanding results and reliability, making it an ideal choice for contractors and DIY enthusiasts alike.
Top Page Image Contents