Bostitch 171430REVA Safety Instructions, AIR Supply and Connections, Loading Tool, Operation

Page 3

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

CAUTION: Additional Safety Protection will be required in some environments. For example, the working area may include exposure to noise level which can lead to hearing damage. The employer and user must ensure that any necessary hearing protection is provided and used by the operator and others in the work area. Some environments will require the use of head protection equipment. When required, the employer and user must ensure that head protection conforming to ANSI Z89.1 is used.

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.

Do not use supply sources which can potentially exceed 200 P.S.I.G. (14kg/cm2 ) as tool may burst, possibly causing injury.

The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected possibly causing injury.

Do not pull trigger or depress contact arm while connected to the air supply as the tool may cycle, possibly causing injury.

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury.

LOADING TOOL

When loading tool: 1.) Never place a hand or any part of body in fastener discharge area of tool; 2.) Never point tool at anyone; 3.) Do not pull the trigger or depress the trip as accidental actuation may occur, possibly causing injury.

OPERATION

Always handle the tool with care: 1.) Never engage in horseplay; 2.) Never pull the trigger unless nose is directed toward the work; 3.) Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury.

The operator must not hold the trigger pulled on contact arm tools except during fastening operation as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact arm tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven possibly causing injury.

Check operation of the contact arm mechanism frequently. Do not use the tool if the arm is not working correctly as accidental driving of a fastener may result. Do not interfere with the proper operation of the contact arm mechanism.

Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury.

Do not drive fasteners close to the edge of the work piece as the wood may split, allowing the fastener to be deflected possibly causing injury.

This nailer produces SPARKS during operation. NEVER use the nailer near flammable substances, gases or vapors including lacquer, paint, benzine, thinner, gasoline, adhesives, mastics, glues or any other material that is -- or the vapors, fumes or byproducts of which are -- flammable, combustible or explosive. Using the nailer in any such environment could cause an EXPLOSION resulting in personal injury or death to user and bystanders.

MAINTAINING THE TOOL

When working on air tools note the warnings in this manual and use extra care when evaluating problem tools.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents N400S Index IntroductionOperation Safety InstructionsAIR Supply and Connections Loading ToolN400S Tool Specifications Lubrication Pusher release tab Loading the N400SLoad Nails Close MagazineDirectional Exhaust Deflector Fastener Depth Control AdjustmentTo Adjust the Fastener Depth Control When using the framing contact armContact Trip Conventional Operation Black Trigger Tool OperationBefore Handling or Operating this Tool Sequential Trip Operation Gray TriggerTool Operation Check Sequential Trip OperationContact Trip Operation Maintaining the Pneumatic Tool Replacement PartsAssembly Procedure for Seals AIR SUPPLY-PRESSURE and VolumeProblem Cause Correction Trouble ShootingIntroducción ÍndiceNota Funcionamiento Instrucciones DE SeguridadSuministro DE Aire Y Conexiones Carga DE LA HerramientaEspecificaciones DE LA Herramienta N400S Lubricación Lengüeta liberación del empujador Carga DE LA Herramienta N400SCargue los clavos Cierre el depósitoPara Ajustar EL Control DE Profundidad DEL Clavo Ajuste DEL Control DE Profundidad DEL ClavoDeflector DE Escape Direccional Extracción DE ClavosFuncionamiento DE LA Herramienta Antes DE Manipular U Operar Esta HerramientaFuncionamiento DEL Disparo Secuencial Gatillo Gris Revisión Funcional DE LA Herramienta Funcionamiento DEL Disparo SecuencialFuncionamiento DEL Disparo DE Contacto Procedimiento DE Ensamblaje Para LOS Sellos Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Piezas DE RepuestoEl vástago de la válvula de disparo Tiene fuga de aire Solución DE ProblemasGarantie Limitée É.-U. et Canada seulement RemarqueChargement DE L’OUTIL Maintenance DE L’OUTILInstructions DE Sécurité Alimentation EN AIR ET ConnexionsCaractéristiques Techniques DES Outils DE LA N400S Lubrification Taquet de verrouillage du pousseur Chargement DES Outils DE LA N400SChargez les clous Fermez le magasinPour Régler LA Profondeur DE Fixation Commande DE Réglage DE Profondeur DE FixationDéflecteur Déchappement Directionnel Retrait DES ClousFonctionnement DE L’OUTIL UtilisationDéclenchement Séquentiel Gâchette Grise Fonctionnement DE LA Butée DE Déclenchement Utilisation DE L’OUTIL SuiteVérification DE L’ÉTAT DE Marche DE L’OUTIL Utilisation DU Déclencheur SéquentielProcédure DE Montage DES Joints Maintenance DE L’OUTIL PneumatiquePression ET Volume DE L’ALIMENTATION D’AIR Pièces DE RechangeRemplacez les joints toriques/joints DépannageNotas Y Registros Remarques ET Rapports

171430REVA, N400S specifications

The Bostitch N400S,171430REVA is a high-performance pneumatic nailer designed for professionals in the construction and woodworking industries. Known for its reliability and versatility, this tool is ideal for various applications, including framing, roofing, and flooring. This article explores the main features, technologies, and characteristics that set the N400S apart from other nailers in the market.

One of the standout features of the Bostitch N400S is its ability to accommodate a wide range of nail sizes. It can handle nails measuring from 1 inch to 2 inches, providing users with the flexibility needed for various projects. The tool employs a one-handed operation design, allowing users to easily adjust the depth of drive without needing additional tools. This feature helps in achieving consistent results across different materials and applications.

The N400S is equipped with advanced technology to enhance user experience and performance. It boasts a powerful and efficient motor that delivers a high degree of performance while minimizing misfires. This is particularly beneficial in fast-paced environments where time is of the essence. Additionally, the nailer features a lightweight aluminum construction, making it easy to handle without causing operator fatigue during prolonged use.

Another notable characteristic of the N400S is its integrated air filter and anti-dust cap. These features help to keep the internal mechanisms clean and free of debris, ensuring optimal performance over time. The tool's rear exhaust directs air away from the user and the work surface, providing a cleaner work environment.

Safety is also a priority with the Bostitch N400S. It includes a sequential firing mode that enhances precision while reducing the risk of accidental discharge. The rubber grip handle provides a comfortable and secure hold, further enhancing control during operation.

In conclusion, the Bostitch N400S,171430REVA nailer stands out for its robust design, user-friendly features, and efficient performance. Its compatibility with various nail sizes, combined with advanced technologies and safety features, makes it a valuable addition to any professional's toolkit. Whether tackling framing jobs or more detailed woodworking tasks, the N400S is engineered to deliver outstanding results and reliability, making it an ideal choice for contractors and DIY enthusiasts alike.
Top Page Image Contents