Bostitch 171430REVA, N400S manual Lubrication

Page 5

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.

FITTINGS:

Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source.

HOSES:

Air hoses should have a minimum of 150 p.s.i. (10.6 kg/cm2) working pressure rating or 150 percent of the maximum pressure that could be produced in the air system. The supply hose should contain a fitting that will provide “quick disconnecting” from the male plug on the tool.

SUPPLY SOURCE:

Use only clean regulated compressed air as a power source for this tool. NEVER USE OXYGEN, COMBUSTIBLE

GASES, OR BOTTLED GASES, AS A POWER SOURCE FOR THIS TOOL AS TOOL MAY EXPLODE.

REGULATOR:

A pressure regulator with an operating pressure of 0 - 125 p.s.i. (0 - 8.79 KG/CM2) is required to control the operatiing pressure for safe operation of this tool. Do not connect this tool to air pressure which can potentially exceed 200 p.s.i. (14 KG/CM2) as tool may fracture or burst, possibly causing injury.

OPERATING PRESSURE:

Do not exceed recommended maximum operating pressure as tool wear will be greatly increased.The air supply must be capable of maintaining the operating pressure at the tool. Pressure drops in the air supply can reduce the tool’s driving power. Refer to “TOOL SPECIFICATIONS” for setting the correct operating pressure for the tool.

FILTER:

Dirt and water in the air supply are major causes of wear in pneumatic tools. A filter will help to get the best performance and minimum wear from the tool. The filter must have adequate flow capacity for the specific installation. The filter has to be kept clean to be effective in providing clean compressed air to the tool. Consult the manufacturer’s instructions on proper maintenance of your filter. A dirty and clogged filter will cause a pressure drop which will reduce the tool’s performance.

LUBRICATION

Frequent, but not excessive, lubrication is required for best performance. Use BOSTITCH Air Tool Lubricant, Mobil Velocite #10, or equivalent. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool maintenance. Only a few drops of oil at a time is necessary. Too much oil will only collect inside the tool and will be noticeable in the exhaust cycle.

COLD WEATHER OPERATION:

For cold weather operation, near and below freezing, the moisture in the air line may freeze and prevent tool operation. We recommend the use of BOSTITCH winter formula air tool lubricant or permanent antifreeze (ethylene glycol) as a cold weather lubricant.

CAUTION: Do not store tools in a cold weather environment to prevent frost or ice formation on the tools operating valves and mechanisms that could cause tool failure.

NOTE:Some commercial air line drying liquids are harmful to “O”-rings and seals – do not use these low temperature air dryers without checking compatibility.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents N400S Index IntroductionAIR Supply and Connections Safety InstructionsLoading Tool OperationN400S Tool Specifications Lubrication Load Nails Loading the N400SClose Magazine Pusher release tabTo Adjust the Fastener Depth Control Fastener Depth Control AdjustmentWhen using the framing contact arm Directional Exhaust DeflectorBefore Handling or Operating this Tool Tool OperationSequential Trip Operation Gray Trigger Contact Trip Conventional Operation Black TriggerContact Trip Operation Tool Operation CheckSequential Trip Operation Assembly Procedure for Seals Replacement PartsAIR SUPPLY-PRESSURE and Volume Maintaining the Pneumatic ToolProblem Cause Correction Trouble ShootingNota IntroducciónÍndice Suministro DE Aire Y Conexiones Instrucciones DE SeguridadCarga DE LA Herramienta FuncionamientoEspecificaciones DE LA Herramienta N400S Lubricación Cargue los clavos Carga DE LA Herramienta N400SCierre el depósito Lengüeta liberación del empujadorDeflector DE Escape Direccional Ajuste DEL Control DE Profundidad DEL ClavoExtracción DE Clavos Para Ajustar EL Control DE Profundidad DEL ClavoFuncionamiento DEL Disparo Secuencial Gatillo Gris Funcionamiento DE LA HerramientaAntes DE Manipular U Operar Esta Herramienta Funcionamiento DEL Disparo DE Contacto Revisión Funcional DE LA HerramientaFuncionamiento DEL Disparo Secuencial Mantenimiento DE LA Herramienta Neumática Presión Y Volumen DEL Suministro DE AirePiezas DE Repuesto Procedimiento DE Ensamblaje Para LOS SellosEl vástago de la válvula de disparo Tiene fuga de aire Solución DE ProblemasGarantie Limitée É.-U. et Canada seulement RemarqueInstructions DE Sécurité Maintenance DE L’OUTILAlimentation EN AIR ET Connexions Chargement DE L’OUTILCaractéristiques Techniques DES Outils DE LA N400S Lubrification Chargez les clous Chargement DES Outils DE LA N400SFermez le magasin Taquet de verrouillage du pousseurDéflecteur Déchappement Directionnel Commande DE Réglage DE Profondeur DE FixationRetrait DES Clous Pour Régler LA Profondeur DE FixationDéclenchement Séquentiel Gâchette Grise Fonctionnement DE L’OUTILUtilisation Vérification DE L’ÉTAT DE Marche DE L’OUTIL Utilisation DE L’OUTIL SuiteUtilisation DU Déclencheur Séquentiel Fonctionnement DE LA Butée DE DéclenchementPression ET Volume DE L’ALIMENTATION D’AIR Maintenance DE L’OUTIL PneumatiquePièces DE Rechange Procédure DE Montage DES JointsRemplacez les joints toriques/joints DépannageNotas Y Registros Remarques ET Rapports

171430REVA, N400S specifications

The Bostitch N400S,171430REVA is a high-performance pneumatic nailer designed for professionals in the construction and woodworking industries. Known for its reliability and versatility, this tool is ideal for various applications, including framing, roofing, and flooring. This article explores the main features, technologies, and characteristics that set the N400S apart from other nailers in the market.

One of the standout features of the Bostitch N400S is its ability to accommodate a wide range of nail sizes. It can handle nails measuring from 1 inch to 2 inches, providing users with the flexibility needed for various projects. The tool employs a one-handed operation design, allowing users to easily adjust the depth of drive without needing additional tools. This feature helps in achieving consistent results across different materials and applications.

The N400S is equipped with advanced technology to enhance user experience and performance. It boasts a powerful and efficient motor that delivers a high degree of performance while minimizing misfires. This is particularly beneficial in fast-paced environments where time is of the essence. Additionally, the nailer features a lightweight aluminum construction, making it easy to handle without causing operator fatigue during prolonged use.

Another notable characteristic of the N400S is its integrated air filter and anti-dust cap. These features help to keep the internal mechanisms clean and free of debris, ensuring optimal performance over time. The tool's rear exhaust directs air away from the user and the work surface, providing a cleaner work environment.

Safety is also a priority with the Bostitch N400S. It includes a sequential firing mode that enhances precision while reducing the risk of accidental discharge. The rubber grip handle provides a comfortable and secure hold, further enhancing control during operation.

In conclusion, the Bostitch N400S,171430REVA nailer stands out for its robust design, user-friendly features, and efficient performance. Its compatibility with various nail sizes, combined with advanced technologies and safety features, makes it a valuable addition to any professional's toolkit. Whether tackling framing jobs or more detailed woodworking tasks, the N400S is engineered to deliver outstanding results and reliability, making it an ideal choice for contractors and DIY enthusiasts alike.
Top Page Image Contents