Bostitch 166066REVE Safety Instructions, AIR Supply and Connections, Loading Tool, Operation

Page 3

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

CAUTION: Additional Safety Protection will be required in some environments. For example, the working area may include exposure to noise level which can lead to hearing damage. The employer and user must ensure that any necessary hearing protection is provided and used by the operator and others in the work area. Some environments will require the use of head protection equipment. When required, the employer and user must ensure that head protection conforming to ANSI Z89.1 is used.

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.

Do not use supply sources which can potentially exceed 200 P.S.I.G. as tool may burst, possibly causing injury.

The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected possibly causing injury.

Do not pull trigger or depress contact arm while connected to the air supply as the tool may cycle, possibly causing injury.

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury.

LOADING TOOL

When loading tool: 1.) Never place a hand or any part of body in fastener discharge area of tool; 2.) Never point tool at anyone; 3.) Do not pull the trigger or depress the trip as accidental actuation may occur, possibly causing injury.

OPERATION

Always handle the tool with care: 1.) Never engage in horseplay; 2.) Never pull the trigger unless nose is directed toward the work; 3.) Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury.

The operator must not hold the trigger pulled on contact arm tools except during fastening operation as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact arm tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven possibly causing injury.

Check operation of the contact arm mechanism frequently. Do not use the tool if the arm is not working correctly as accidental driving of a fastener may result. Do not interfere with the proper operation of the contact arm mechanism.

Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury.

Do not drive fasteners close to the edge of the work piece as the wood may split, allowing the fastener to be deflected possibly causing injury.

This nailer produces SPARKS during operation. NEVER use the nailer near flammable substances, gases or vapors including lacquer, paint, benzine, thinner, gasoline, adhesives, mastics, glues or any other material that is -- or the vapors, fumes or byproducts of which are -- flammable, combustible or explosive. Using the nailer in any such environment could cause an EXPLOSION resulting in personal injury or death to user and bystanders.

Never use belt hook with contact trigger (black trigger) operated tools.

MAINTAINING THE TOOL

When working on air tools note the warnings in this manual and use extra care when evaluating problem tools.

-3-

Page 2 Page 4
Image 3
Page 2 Page 4
Contents FN16250 Index IntroductionOperation Safety InstructionsAIR Supply and Connections Loading ToolFN16250 Tool Specifications Regulator FittingsHoses Supply SourceTo Prevent Accidental Injuries Loading the FN16250Contact Trip Operation Tool OperationBefore Handling or Operating this Tool Trigger OperationTool Must Cycle Tool Operation CheckTrigger Operated Tool Tool Must not CycleAIR SUPPLY-PRESSURE and Volume DIAL-A-DEPTH Fastener Control AdjustmentReplacement Parts Assembly Procedure for SealsProblem Cause Correction Trouble ShootingPage Introducción ÍndiceNota Operación Instrucciones DE SeguridadSuministro DE Aire Y Conexiones AL Cargar LA HerramientaEspecificaciones DE LA Herramienta FN16250 Regulador ConexionesMangueras Fuente DE SuministroAdvertencia Para Impedir Lesiones Accidentales Cómo Cargar EL FN16250Operación DE Disparo Secuencial Operación DE LA HerramientaAntes DE Manejar U Operar Esta Herramienta Operación DE Disparo POR ContactoLA Herramienta no Debe Efectuar SU Ciclo Verificación DE LA Operación DE LA HerramientaHerramienta Operada POR Gatillo Operación POR Disparo SecuencialPartes DE Reemplazo Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Ajuste DEL Control DE Fondo DEL Sujetador DIAL-A-DEPTHDiagnóstico DE Falla Problema Causa CorrecciónPage Remarque SommaireFonctionnement Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement Chargement DE L’APPAREILOpération Caractéristiques DU FN16250Régulateur RaccordementsTuyaux Alimentation EN AIR CompriméPour Prévenir UN Accident Chargement DU FN16250Avant DE Manipuler OU D’UTILISER CET Outil Fonctionnement DE L’APPAREILSystème DE Sécurité AU COUP-PAR-COUP Vérification DU Système DE DéclenchementDéclenchement PAR LA Détente Système DE Sécurité À LA VoléeProcédure D’ASSEMBLAGE DES Garnitures Alimentation D’AIR Pression VolumeEntretien DE L’APPAREIL Pièces DE RechangeProblème Cause Correction Problèmes DE Fonctionnement

166066REVE specifications

The Bostitch 166066REVE is a versatile and robust electric nailer designed to enhance productivity in various woodworking and construction projects. This model stands out for its efficient performance and user-friendly features, making it a popular choice among professionals and DIY enthusiasts alike. The 166066REVE is engineered to provide a reliable solution for fastening applications, from framing to finishing.

One of the main features of the Bostitch 166066REVE is its impressive firing speed, allowing users to drive nails quickly and efficiently. This electric nailer offers a rapid-fire mode that enables users to complete projects more swiftly, which is especially beneficial for larger tasks that require substantial fastening repetition. The tool can accommodate a variety of nail sizes and types, enhancing its versatility for different applications.

The ergonomic design of the Bostitch 166066REVE ensures comfort during extended use. Its lightweight construction minimizes user fatigue, making it easier to handle throughout the day. Additionally, the handle is designed with rubber material that provides a secure grip, improving control and precision while working on intricate projects.

Equipped with advanced safety features, the 166066REVE includes a no-mar tip that protects work surfaces from scratches and dents, ensuring clean and professional results. The nailer’s safety trigger prevents accidental firing, adding another layer of security for users. The depth adjustment dial allows for precise control over the depth of nail penetration, accommodating various materials and ensuring optimal results every time.

In terms of technology, the Bostitch 166066REVE incorporates a direct drive system that delivers consistent power and performance. This system reduces the risk of misfires and helps maintain pressure for superior nail driving capabilities. Additionally, the nailer features a tool-free jam release mechanism, allowing users to quickly and easily clear any obstructions without wasting time or effort.

Overall, the Bostitch 166066REVE is a reliable electric nailer that combines speed, power, and user-friendly features. Its ergonomic design, advanced safety elements, and versatile capabilities make it an ideal choice for both amateur craftsmen and seasoned professionals. Whether tackling framing projects, cabinetry, or trim work, the Bostitch 166066REVE provides the performance and durability needed to achieve exceptional results.
Top Page Image Contents