Bostitch 166066REVE Tool Operation, Before Handling or Operating this Tool, Trigger Operation

Page 7

TOOL OPERATION

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

BEFORE HANDLING OR OPERATING THIS TOOL:

I.READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL.

II.REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL.

There are three available systems on BOSTITCH pneumatic tools. They are:

1. TRIGGER OPERATION 2. CONTACT TRIP OPERATION 3. SEQUENTIAL TRIP OPERATION

OPERATION

1.TRIGGER OPERATION:

A TRIGGER OPERATED tool requires a single action to drive a fastener. Each time the trigger is pulled the tool will drive a fastener. The trigger operated model is intended for use only when a contact trip or sequential trip cannot be used due to the requirements of the application.

2.CONTACT TRIP OPERATION:

The CONTACT TRIP MODEL tool contains a contact trip that operates in conjunction with the trigger to drive a fastener. There are two methods of operation to drive fasteners with a contact trip tool.

A. SINGLE FASTENER PLACEMENT: To operate the tool in this manner, first position the contact trip on the work surface, WITHOUT PULLING THE TRIGGER. Depress the contact trip until the nose touches the work surface and then pull the trigger to drive a fastener. Do not press the tool against the work with extra force. Instead, allow the tool to recoil off the work surface to avoid a second unwanted fastener. Remove your finger from the trigger after each operation.

B. RAPID FASTENER OPERATION: To operate the tool in this manner, hold the tool with the contact trip pointing towards but not touching the work surface. Pull the trigger and then tap the contact trip against the work surface using a bouncing motion. Each depression of the contact trip will cause a fastener to be driven.

The operator must not hold the trigger pulled on contact trip tools except during fastening operation, as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact trip tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven, possibly causing injury.

Never use belt hook with contact trigger (black trigger) operated tools.

3.SEQUENTIAL TRIP OPERATION:

The SEQUENTIAL TRIP MODEL contains a contact trip that operates in conjunction with the trigger to drive a fastener. To operate a sequential trip tool, first position the contact trip on the work surface WITHOUT PULLING THE TRIGGER. Depress the contact trip and then pull the trigger to drive a fastener. As long as the contact trip is contacting the work and is held depressed, the tool will drive a fastener each time the trigger is depressed. If the contact trip is allowed to leave the work surface, the sequence described above must be repeated to drive another fastener.

-7-

Page 6 Page 8
Image 7
Page 6 Page 8
Contents FN16250 Index IntroductionOperation Safety InstructionsAIR Supply and Connections Loading ToolFN16250 Tool Specifications Regulator FittingsHoses Supply SourceTo Prevent Accidental Injuries Loading the FN16250Contact Trip Operation Tool OperationBefore Handling or Operating this Tool Trigger OperationTool Must Cycle Tool Operation CheckTrigger Operated Tool Tool Must not CycleAIR SUPPLY-PRESSURE and Volume DIAL-A-DEPTH Fastener Control AdjustmentReplacement Parts Assembly Procedure for SealsProblem Cause Correction Trouble ShootingPage Índice IntroducciónNota Operación Instrucciones DE SeguridadSuministro DE Aire Y Conexiones AL Cargar LA HerramientaEspecificaciones DE LA Herramienta FN16250 Regulador ConexionesMangueras Fuente DE SuministroAdvertencia Para Impedir Lesiones Accidentales Cómo Cargar EL FN16250Operación DE Disparo Secuencial Operación DE LA HerramientaAntes DE Manejar U Operar Esta Herramienta Operación DE Disparo POR ContactoLA Herramienta no Debe Efectuar SU Ciclo Verificación DE LA Operación DE LA HerramientaHerramienta Operada POR Gatillo Operación POR Disparo SecuencialPartes DE Reemplazo Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Ajuste DEL Control DE Fondo DEL Sujetador DIAL-A-DEPTHDiagnóstico DE Falla Problema Causa CorrecciónPage Remarque SommaireFonctionnement Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement Chargement DE L’APPAREILOpération Caractéristiques DU FN16250Régulateur RaccordementsTuyaux Alimentation EN AIR CompriméPour Prévenir UN Accident Chargement DU FN16250Avant DE Manipuler OU D’UTILISER CET Outil Fonctionnement DE L’APPAREILSystème DE Sécurité AU COUP-PAR-COUP Vérification DU Système DE DéclenchementDéclenchement PAR LA Détente Système DE Sécurité À LA VoléeProcédure D’ASSEMBLAGE DES Garnitures Alimentation D’AIR Pression VolumeEntretien DE L’APPAREIL Pièces DE RechangeProblème Cause Correction Problèmes DE Fonctionnement

166066REVE specifications

The Bostitch 166066REVE is a versatile and robust electric nailer designed to enhance productivity in various woodworking and construction projects. This model stands out for its efficient performance and user-friendly features, making it a popular choice among professionals and DIY enthusiasts alike. The 166066REVE is engineered to provide a reliable solution for fastening applications, from framing to finishing.

One of the main features of the Bostitch 166066REVE is its impressive firing speed, allowing users to drive nails quickly and efficiently. This electric nailer offers a rapid-fire mode that enables users to complete projects more swiftly, which is especially beneficial for larger tasks that require substantial fastening repetition. The tool can accommodate a variety of nail sizes and types, enhancing its versatility for different applications.

The ergonomic design of the Bostitch 166066REVE ensures comfort during extended use. Its lightweight construction minimizes user fatigue, making it easier to handle throughout the day. Additionally, the handle is designed with rubber material that provides a secure grip, improving control and precision while working on intricate projects.

Equipped with advanced safety features, the 166066REVE includes a no-mar tip that protects work surfaces from scratches and dents, ensuring clean and professional results. The nailer’s safety trigger prevents accidental firing, adding another layer of security for users. The depth adjustment dial allows for precise control over the depth of nail penetration, accommodating various materials and ensuring optimal results every time.

In terms of technology, the Bostitch 166066REVE incorporates a direct drive system that delivers consistent power and performance. This system reduces the risk of misfires and helps maintain pressure for superior nail driving capabilities. Additionally, the nailer features a tool-free jam release mechanism, allowing users to quickly and easily clear any obstructions without wasting time or effort.

Overall, the Bostitch 166066REVE is a reliable electric nailer that combines speed, power, and user-friendly features. Its ergonomic design, advanced safety elements, and versatile capabilities make it an ideal choice for both amateur craftsmen and seasoned professionals. Whether tackling framing projects, cabinetry, or trim work, the Bostitch 166066REVE provides the performance and durability needed to achieve exceptional results.
Top Page Image Contents