Operation, Protective clothing and take | Campbell Hausfeld WG2060

Wire Feed Arc Welder

General Safety

supported and grounded prior to

beginning any electric arc welding

! WARNING

(Continued)

Electric arc welding

operation.

NOTE: Note means any additional

operations produce

● Spread out coiled welding cable

information pertaining to the product

intense light and heat

before use to avoid overheating and

and ultraviolet (UV)

or its proper usage.

damage to insulation.

rays. This intense light

Never immerse

and UV rays can cause injury to eyes and

WARNING

! DANGER

wire or wire feed

skin. Take all precautions described in

Always keep a fire

this manual to reduce the possibility of

gun in water. If welder becomes wet for

extinguisher accessible

injury to eyes and skin.

any reason, be absolutely certain it is

while performing arc

completely clean and dry before use!

● All persons operating this equipment

welding operations.

● Always shut equipment off and

or in the area while equipment is in

● Before starting or

unplug power cord prior to moving

use, must wear protective welding gear

servicing any electric arc welder, read

the unit.

including: welding helmet or shield

and understand all

● Always attach the work lead first.

with at least shade 10 lens, flame

instructions. Failure

● Verify work piece is securely

resistant clothing, leather welding

to follow safety

grounded.

gloves and full foot protection.

precautions or

MANUAL

Never look at arc

● Always shut off electric arc welding

! WARNING

instructions can

welding operations

cause equipment

equipment when not in use and cut off

without eye protection as described

damage and/or serious personal

any excess wire from wire feed gun.

above. Never use a shade filter lens

that is cracked, broken, or rated below

injury or death.

● Never allow any part of the body to

number 10. Warn others in the area not

● All installation, maintenance, repair

touch flux-cored wire and ground or

to look at the arc.

grounded work piece at the same

and operation of this equipment

should be performed by qualified

time.

! WARNING

● Awkward welding conditions and

Electric arc welding

persons only in accordance with

operations cause sparks

national, state, and local codes.

positions can be electrically hazardous.

and heat metal to

When crouching, kneeling or at

temperatures that can

! WARNING

elevations, be sure to insulate all

cause severe burns! Use

Improper use of electric

conductive parts, wear appropriate

protective gloves and clothing when

arc welders can cause

protective clothing and take

performing any metal working

electric shock, injury,

operation. Take all precautions described

precautions to prevent injury from falls.

and death! Take all

in this manual to reduce the possibility

precautions described in

● Never attempt to use this equipment

of skin and clothing burns.

this manual to reduce the possibility of

at current settings or duty cycles higher

● Make sure all persons in welding

electric shock.

than specified on equipment labels.

area are protected from heat, sparks

● Verify all components of the arc

● Never use an electric arc welder to

and ultraviolet rays. Use additional

welder are clean and in good

thaw frozen pipes.

face shields and flame resistant

condition prior to operating welder.

barriers as needed.

Be sure insulation on all cables, wire

! WARNING

● Never touch work pieces until

feed gun and power cord is not

damaged. Always repair or replace

Flying sparks and hot

completely cooled.

metal can cause injury.

damaged components before

operating the welder. Always keep

As welds cool, slag can

! WARNING

be thrown off. Take all

Heat and sparks

welder panels, shields, etc. in place

precautions described in

produced during

when operating welder.

this manual to reduce

electric arc welding and

the possibility of injury from flying

● Always wear dry, protective

other metal working

sparks and hot metal.

clothing, welding gloves and

operations can ignite

● Wear ANSI approved face shield or

flammable and explosive materials!

insulated footwear when operating

safety glasses with side shield

Take all precautions described in this

unit.

protection when chipping or

manual to reduce the possibility of

● Always operate welder in a clean,

flames and explosions.

grinding metal parts.

dry, well ventilated area. Do not

● Remove all flammable materials

● Wear ear plugs when welding

operate welder in humid, wet, rainy

within 35 feet (10.7 meters) of

overhead to prevent spatter or slag

or poorly ventilated areas.

welding arc. If removal is not

from falling into ears.

●	Be sure work piece is properly	possible, tightly cover flammable

materials with fire proof covers.

www.chpower.com

Notes

Notas

Models WG2060 and WG2064

Modèles WG2060 et WG2064

Modelos WG2060 y WG2064