Grizzly G0601 owner manual Safety Instructions for Machinery

Page 12

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

 

WILL result in death or serious injury.

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

COULd result in death or serious injury.

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this owner’s manual BEFORE using machine. Untrained users can be seriously hurt.

EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved safety glasses.

HAzARdOUS dUST. Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator to reduce your risk.

WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips which could cause a loss of work- piece control.

HEARING PROTECTION. Always wear hear- ing protection when operating or observiing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

MENTAL ALERTNESS. Be mentally alert when running machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

-10-

Model G0442/G0601 (Mfg Since 8/10)

Page 11 Page 13
Image 12
Page 11 Page 13
Contents HP Cyclone Dust Collector Page Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Identification Model G0442 shownMachine Data Sheet Bag Information Performance Curve G0601 Machine Data Sheet Air Suction Cap CFM @1.9 in. S.P G0601 Performance Curve Safety Safety Instructions for MachineryUnattended OPERATION. Never­ leave­ Additional Safety Instructions for Dust Collectors Power Supply AvailabilityFull-Load Current Rating Circuit RequirementsG0601 Circuit Requirements for 220V G0601 Circuit Requirements for 440VGrounding Instructions Grounding & Plug RequirementsExtension Cords 220V Only 50 ftTo rewire the Model G0601 for 440V opera- tion G0601 440V ConversionCorrecting Phase Polarity G0601 Only Setup Needed for SetupUnpacking Description QtyCollector Box Contents Figure Qty InventoryStand Box Contents Figure Qty Contents of Filter Boxes Figure QtyHardware Recognition Chart Site Considerations Using Machine Mounts Mounting to Shop FloorBolting to Concrete Floors Assembly Foam tape attached to the intake Cylinder Aligning the mounting holes Tape Cyclone vacuum tube and hose Attachment Page Tip Use an adhesive to keep the seal in place Connecting the vacuum hose Model G0442/G0601 Mfg Since 8/10 Switch mounted to stand Model G0442/G0601 Mfg Since 8/10 Test Run For Model G0601 OnlyTo test run the dust collection system System Design GeneralDucting Materials Metal DuctFlexible Duct Plastic DuctDesigning Ducting System Decide Who Will DesignSketch The Shop Layout Sketch a Basic Duct LayoutDetermine CFM of Each Machine Machine ApproximateDetermining Main Line Duct Diameter MachineDetermining Branch Line Duct Diameter Multiple Dust PortsTwo Machines on Same Branch Line Total CFM Branch Line SizeCalculating Duct Resistance Duct Approximate DiaLoss Per Foot Fitting 90˚ 45˚ Dia Elbow WyeYClosest CFM 1785System Grounding Remote Control OperationsControl Box Panel Accessories Metal Duct Starter KitMetal Elbows Metal BranchesReducers & Adapters G6252-4 Floor Sweep G7341-5 Floor Sweep G7342-6 Floor SweepMaintenance Cleaning FiltersSchedule Emptying DrumRinsing Filter Removing/Replacing FilterTools Needed Qty To replace the canister filterPage Service TroubleshootingRefer to Designing Ducting System, beginning Wiring Wiring Safety InstructionsG0442 Wiring Diagram Model G0442G0601 Wiring Diagram Model G0601Parts MainG0442 Only Parts List G0601 Only Parts ListG0442/G0601 Common Parts List Description Page Page Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY
Top Page Image Contents