Woodstock W1677, W1711 owner manual Machine Placement, Cleaning Machine

Page 19

W1677/W1711 10" Table Saw

Machine Placement

Cleaning Machine

•Floor Load: This machine distributes a heavy load in a small footprint. Some floors may require additional bracing to support both machine and operator.

•Working Clearances: Consider the following when establishing a location for your machine:

—Existing and anticipated needs

—Size of material to be processed

—Space for auxiliary stands, work tables or other machinery

—Room to perform maintenance inside the cabinet.

•Lighting: Lighting should be bright enough to eliminate shadow and prevent eye strain.

•Electrical: Electrical circuits must be dedicated or large enough to handle amperage requirements. Outlets must be located near each machine, so high-traffic areas are clear of power cords. Follow local electrical codes for proper installation of new lighting, outlets, or circuits.

USE helpers or power lifting equipment to lift this machine. Otherwise, serious personal injury may occur.

MAKE your shop “child safe.” Ensure that your workplace is inaccessible to youngsters by closing and locking all entrances when you are away. NEVER allow untrained visitors in your shop when assem- bling, adjusting or operat- ing equipment.

The unpainted parts of your machine type are coated with a shipping grease that protects them from corrosion during shipment. This coat- ing does its job well, but requires a little elbow grease to remove.

The shipping grease can be cleaned off with a solvent, petroleum or citrus-based degreaser. DO NOT use chlorine-based solvents such as brake parts cleaner or acetone—if you happen to splash some onto a painted surface, you will ruin the finish.

Here is one easy and popular method for clean- ing the shipping grease: Soak the grease in WD-40®or a similar product, wait five minutes, scrape most of the grease off with a plastic putty knife or other straight edge that won't scratch the cast iron, re-soak, then wipe down with a shop rag.

NEVER use gasoline or other petroleum-based solvents to clean with. Most have low flash points, which make them extremely flammable. A risk of explosion and burning exists if these products are used. Serious personal injury may occur if this warning is ignored!

ALWAYS work in well- ventilated areas far from possible ignition sources when using solvents to clean machinery. Many solvents are toxic when inhaled or ingested. Use care when disposing of waste rags and towels to be sure they DO NOT create fire or environmental hazards.

-17-

SETUP

Page 18 Page 20
Image 19
Page 18 Page 20
Contents LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support IntroductionW1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and FeaturesStandard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential InjuriesUse featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible KickbackCommon Terms Grounding Electrical220V Operation Extension CordsBox Inventory Figures 12 Qty SetupUnpacking InventoryLong Rails Figure Qty Shop Fox Classic Fence InventoryInventory Needed for Your Saw Standard Rails Figure QtyFlat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence InventoryCleaning Machine Machine PlacementMobile Base AssemblyTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Before you test run the machine, do these steps Test RunTo test run the table saw, do these steps Feed Rate OperationsGeneral Blade HeightBlade Material Blade SelectionBlade Types To change blades, do these steps Changing BladesThrough Cuts Through vs. Non-Through CutsNon-Through Cuts To make a rip cut, do these steps When using the tilting mechanismRip Cuts Blade Tilt/Bevel CutsTo cut a miter, do these steps To crosscut using the miter gauge, do these stepsCross Cuts Miter CutsTo use a stacked or wobble dado blade, do these steps Dado CutsTo cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping bladeTo cut rabbets with the dado blade, do these steps Rabbet CutsClearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these stepsTo build the resaw barrier, do these steps ResawingResaw Barrier Components Needed for the Resaw BarrierComponents Needed for the Auxiliary Fence Auxiliary FenceTo build the auxiliary fence, do these steps Components Needed for Resawing Resawing OperationsTo perform resawing operations, do these steps Outfeed roller table Aftermarket Safety AccessoriesHere are some of the basic items you may want to consider Shop-Made Safety AccessoriesTable & Base MaintenanceCleaning BeltsBlade Tilt Stop Bolts ServiceTo set the stop bolts on the trunnion, do these steps To adjust the geared bearing housing, do these steps To adjust the trunnion assembly, do these stepsBlade Alignment Measuring blade to miter slot Miter Slot Parallel to BladeTo shim an extension wing, do these steps Shimming WingsTo check and align the splitter to the blade, do these steps Splitter AdjustmentTo set the miter gauge pointer, do these steps Angle PointerMiter Gauge To set the angle pointer, do these stepsReplacing V-Belts Adjusting FenceTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical TroubleshootingPossible Cause Corrective Action Table Saw OperationsTable/Body Breakdown PartsPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA
Top Page Image Contents