Woodstock W1677, W1711 owner manual XPB15

Page 57

W1677/W1711 10" Table Saw

REF	PART�#	DESCRIPTION
57	XPB15	HEX�BOLT�5/16-18�X�3/8
57-1	XPW07	FLAT�WASHER�5/16
60	XPB07	HEX�BOLT�5/16-18�X�3/4
61	XPW07	FLAT�WASHER�5/16
62	X1677062	BRACKET
72	X1677072	SHAFT
73	X1677073	UPR�BLADE�GUARD�BRACKET
74	X1677074	LWR�BLADE�GUARD�BRACKET
140	XPB11	HEX�BOLT�5/16-18�X�1-1/2
141	XPW07	FLAT�WASHER�5/16
142	XPLW01	LOCK�WASHER�5/16
143	XPN02	HEX�NUT�5/16-18
144	XPB03	HEX�BOLT�5/16-18�X�1
145	XPSS02	SET�SCREW�5/16-18�X�3/8
200	X1677200	COMPLETE�MITER�GAUGE

REF	PART�#	DESCRIPTION
201	X1677201	MITER�GAUGE�BODY
201-1	X1677201-1	RIVET�2�X�4
201-2	X1677201-2	MITER�GAUGE�SCALE
202	X1677202	MITER�GAUGE�HANDLE
203	X1677203	STAR�KNOB�5/16-18�X�1-1/4
204	XPW07	FLAT�WASHER�5/16
205	X1677205	POINTER
206	XPFH04	FLAT�HD�SCR�1/4-20�X�5/8
207	X1677207	MITER�SLIDE�BAR
208	X1677208	SPECIAL�SCREW
209	X1677209	SPECIAL�WASHER
210	XPSS31	SET�SCREW�10-24�X�5/8
300	X1677300	BLADE�GUARD�ASSEMBLY
301	X1677301	BLADE�GUARD�LABEL

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.

PARTS

-55-

Image 57

Contents LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support IntroductionW1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and FeaturesStandard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential InjuriesUse featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible KickbackCommon Terms 220V Operation ElectricalExtension Cords GroundingUnpacking SetupInventory Box Inventory Figures 12 QtyInventory Needed for Your Saw Shop Fox Classic Fence InventoryStandard Rails Figure Qty Long Rails Figure QtyFlat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence InventoryCleaning Machine Machine PlacementAssembly Mobile BaseTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Test Run Before you test run the machine, do these stepsTo test run the table saw, do these steps General OperationsBlade Height Feed RateBlade Selection Blade MaterialBlade Types To change blades, do these steps Changing BladesThrough vs. Non-Through Cuts Through CutsNon-Through Cuts Rip Cuts When using the tilting mechanismBlade Tilt/Bevel Cuts To make a rip cut, do these stepsCross Cuts To crosscut using the miter gauge, do these stepsMiter Cuts To cut a miter, do these stepsTo use a stacked or wobble dado blade, do these steps Dado CutsTo cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping bladeTo cut rabbets with the dado blade, do these steps Rabbet CutsClearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these stepsResaw Barrier ResawingComponents Needed for the Resaw Barrier To build the resaw barrier, do these stepsAuxiliary Fence Components Needed for the Auxiliary FenceTo build the auxiliary fence, do these steps Resawing Operations Components Needed for ResawingTo perform resawing operations, do these steps Outfeed roller table Aftermarket Safety AccessoriesHere are some of the basic items you may want to consider Shop-Made Safety AccessoriesCleaning MaintenanceBelts Table & BaseService Blade Tilt Stop BoltsTo set the stop bolts on the trunnion, do these steps To adjust the trunnion assembly, do these steps To adjust the geared bearing housing, do these stepsBlade Alignment Measuring blade to miter slot Miter Slot Parallel to BladeTo shim an extension wing, do these steps Shimming WingsTo check and align the splitter to the blade, do these steps Splitter AdjustmentMiter Gauge Angle PointerTo set the angle pointer, do these steps To set the miter gauge pointer, do these stepsAdjusting Fence Replacing V-BeltsTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical TroubleshootingPossible Cause Corrective Action Table Saw OperationsTable/Body Breakdown PartsPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA