Woodstock W1711, W1677 owner manual Standard Safety Instructions

Page 8

SAFETY

W1677/W1711 10" Table Saw

SAFETY

READ MANUAL BEFORE OPERATING MACHINE. FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY.

Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury.

This symbol is used to alert the user to useful information about proper NOTICE operation of the equipment, and/or a situation that may cause damage

to the machinery.

Standard Safety Instructions

1.READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious injury hazards to untrained users.

2.ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eye- glasses only have impact resistant lenses—they are NOT safety glasses.

3.ALWAYS WEAR AN NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.

4.ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage.

5.WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to contain long hair and wear non-slip footwear.

6.NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.

Be mentally alert at all times when running machinery.

7.ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood.

8.KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area.

9.MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys.

-6-

Image 8
Contents LEFT-TILT Table SAW Page Table of Contents Introduction Woodstock Technical SupportW1677 Series Specifications W1711 Series Specifications Controls and Features Fence controls Blade Guard/Splitter Miter GaugeSafety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Avoiding Potential Injuries Unplug saw before changing bladesUse featherboards when possible To protect against kickback Kickback Use a zero-clearance table insert whenever possibleCommon Terms Electrical 220V OperationExtension Cords GroundingSetup UnpackingInventory Box Inventory Figures 12 QtyShop Fox Classic Fence Inventory Inventory Needed for Your SawStandard Rails Figure Qty Long Rails Figure QtyShop Fox Original Fence Inventory Flat Washers 3⁄ 8 Rail/Ext TableMachine Placement Cleaning MachineTo assemble your table saw, do these steps AssemblyMobile Base Motor shipping brace Installing blade Adjusting table insert flush To test run the table saw, do these steps Test RunBefore you test run the machine, do these steps Operations GeneralBlade Height Feed RateBlade Types Blade SelectionBlade Material Changing Blades To change blades, do these stepsNon-Through Cuts Through vs. Non-Through CutsThrough Cuts When using the tilting mechanism Rip CutsBlade Tilt/Bevel Cuts To make a rip cut, do these stepsTo crosscut using the miter gauge, do these steps Cross CutsMiter Cuts To cut a miter, do these stepsDado Cuts To use a stacked or wobble dado blade, do these stepsFirst cut when making a dado With a standard ripping blade To cut dadoes with a standard blade, do these stepsRabbet Cuts To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps Clearly mark the width of the rabbet cut on WorkpieceResawing Resaw BarrierComponents Needed for the Resaw Barrier To build the resaw barrier, do these stepsTo build the auxiliary fence, do these steps Auxiliary FenceComponents Needed for the Auxiliary Fence To perform resawing operations, do these steps Resawing OperationsComponents Needed for Resawing Aftermarket Safety Accessories Outfeed roller tableShop-Made Safety Accessories Here are some of the basic items you may want to considerMaintenance CleaningBelts Table & BaseTo set the stop bolts on the trunnion, do these steps ServiceBlade Tilt Stop Bolts Blade Alignment To adjust the trunnion assembly, do these stepsTo adjust the geared bearing housing, do these steps Miter Slot Parallel to Blade Measuring blade to miter slotShimming Wings To shim an extension wing, do these stepsSplitter Adjustment To check and align the splitter to the blade, do these stepsAngle Pointer Miter GaugeTo set the angle pointer, do these steps To set the miter gauge pointer, do these stepsTo replace the V-belts, do these steps Adjusting FenceReplacing V-Belts W1677 Wiring Diagram W1711 Wiring Diagram Troubleshooting Motor & ElectricalTable Saw Operations Possible Cause Corrective ActionParts Table/Body BreakdownPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA