Woodstock W1677, W1711 owner manual Service, Blade Tilt Stop Bolts

Page 41

W1677/W1711 10" Table Saw

SERVICE

General

This section covers the most common service adjustments or procedures that may need to be made during the life of your machine.

If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz.

Blade Tilt Stop Bolts

The table saw trunnion features 45° and 90° stop bolts on the geared trunnion that, when adjusted correctly, stop the blade exactly at 45° and 90° during blade adjust- ments.

To set the stop bolts on the trunnion, do these steps:

1.DISCONNECT SAW FROM POWER!

2.Position the blade tilt to zero (see indicator on the front of the saw), and raise the blade several inches above the table.

3.Place a machinist’s square flat on the table and slide it alongside the blade. The square should con- tact the blade evenly from bottom to top. Make sure that a blade tooth does not obstruct the movement of the square.

4.Adjust the handwheel until the square is flush with the blade. Loosen the tilt indicator arrow, set to zero, and retighten. Loosen and adjust the stop bolt on the left side of the front trunnion to allow a 90° stop point. Refer to Figure 63 for details.

5.Turn the blade angle handwheel until the angle indi- cator points at the desired angle.

6.Tighten the handwheel locking knob.

7.Repeat Steps 1-6for setting the blade to 45° and adjust the 45° stop bolt on the right side of the front trunnion. Use the 45° side of a combo square or a bevel gauge set at 45°.

MAKE SURE that your machine is unplugged during all service proce- dures! If this warning is ignored, seri- ous personal injury may occur.

��

��

Figure 63. Blade tilt stop bolts.

SERVICE

-39-

Image 41

Contents LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support IntroductionW1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and FeaturesStandard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential InjuriesUse featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible KickbackCommon Terms 220V Operation ElectricalExtension Cords GroundingUnpacking SetupInventory Box Inventory Figures 12 QtyInventory Needed for Your Saw Shop Fox Classic Fence InventoryStandard Rails Figure Qty Long Rails Figure QtyFlat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence InventoryCleaning Machine Machine PlacementTo assemble your table saw, do these steps AssemblyMobile Base Motor shipping brace Installing blade Adjusting table insert flush To test run the table saw, do these steps Test RunBefore you test run the machine, do these steps General OperationsBlade Height Feed RateBlade Types Blade SelectionBlade Material To change blades, do these steps Changing BladesNon-Through Cuts Through vs. Non-Through CutsThrough Cuts Rip Cuts When using the tilting mechanismBlade Tilt/Bevel Cuts To make a rip cut, do these stepsCross Cuts To crosscut using the miter gauge, do these stepsMiter Cuts To cut a miter, do these stepsTo use a stacked or wobble dado blade, do these steps Dado CutsTo cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping bladeTo cut rabbets with the dado blade, do these steps Rabbet CutsClearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these stepsResaw Barrier ResawingComponents Needed for the Resaw Barrier To build the resaw barrier, do these stepsTo build the auxiliary fence, do these steps Auxiliary FenceComponents Needed for the Auxiliary Fence To perform resawing operations, do these steps Resawing OperationsComponents Needed for Resawing Outfeed roller table Aftermarket Safety AccessoriesHere are some of the basic items you may want to consider Shop-Made Safety AccessoriesCleaning MaintenanceBelts Table & BaseTo set the stop bolts on the trunnion, do these steps ServiceBlade Tilt Stop Bolts Blade Alignment To adjust the trunnion assembly, do these stepsTo adjust the geared bearing housing, do these steps Measuring blade to miter slot Miter Slot Parallel to BladeTo shim an extension wing, do these steps Shimming WingsTo check and align the splitter to the blade, do these steps Splitter AdjustmentMiter Gauge Angle PointerTo set the angle pointer, do these steps To set the miter gauge pointer, do these stepsTo replace the V-belts, do these steps Adjusting FenceReplacing V-Belts W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical TroubleshootingPossible Cause Corrective Action Table Saw OperationsTable/Body Breakdown PartsPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA